相干光被粗糙表面散射后衍射谱的分布探讨

利用傅立叶光学的基本原理，对相干光波被粗糙表面散射后衍射谱的分布进行探讨。     

Comparison of interfaces in Ti composites reinforced with uncoated and TiB2/C-coated SiC fibres

Interfaces play an important role in determining the mechanical properties of composite materials. The interfaces established between a titanium-alloy matrix (Ti-6Al-4V) and uncoated and TiB₂/C-coated SiC fibres are analysed by scanning electron microscopy, transmission electron microscopy and X-ray techniques. Emphasis is placed upon the interfacial morphology and microstructure, identification of reaction products, and the stability of the coating layer. Complex multi-reaction layers are observed frequently in the interfacial zones. Previous, often contradictory, reports about the interlayers are reviewed. Experimental observation demonstrates that the type and distribution of interlayers vary in a given system, due to prolonged treatment of the samples at temperature. The formation and distribution of the interlayers are discussed further, with respect to these and previous findings. Methods of reducing interfacial reactivity are discussed.     

A relation between interfacial and bulk properties along the saturation curve

A liquid-vapor interface in thermal equilibrium was considered, where the pressure tensor depends upon the density (z) and the position z. The surface tension coefficient results are parametrized with the bulk compressibility, liquid-vapor density difference, and interfacial width along the saturation curve. Previous results at the triple and critical points reported by other investigators are verified. Also included is a plot of the computed results using the parametric equation and experimental data for different substances.     

An enhanced,acoustic emission-based,single-fiber-composite test

In the single-fiber-composite (SFC) test, a fiber imbedded in a matrix is loaded in tension, resulting in a fragmentation of the fiber. In the conventional version of this test, the final fiber fragmentation length distribution is used with a micro-mechanical model to determine the average fiber/matrix interfacial shear stress. In the enhanced version of this test, one also determines the applied stress at each fiber fracture, and from this, one can evaluate the strength of the fiber at short gage lengths. In our measurement system, we utilize an acoustic emission (AE) technique to detect the fiber fractures and to locate the fiber breaks and so determine both the fiber failure stresses as well as the fiber fragmentation lengths while the test is in progress. Critical to the success of this test is a broadband AE system that utilizes point-like AE sensors, procedures for evaluatingin situ, the wavespeed of the first wave arrival and signal processing techniques for determining the arrival time of this signal as precisely as possible for a broad range of wave shapes. Here we describe the application of such an enhanced SFC test procedure to investigate the failure of a Nicalon fiber in an epoxy matrix.     

The statistical modeling of surface roughness in high-speed flat end milling

Surface roughness is one of the most important requirements in machining process. The surface roughness value is a result of the tool wear. When tool wear increase, the surface roughness also increases. The determination of the sufficient cutting parameters is a very important process obtained by means of both minimum surface roughness values and long tool life. The statistical models were developed to predict the surface roughness.This paper presents the development of a statistical model for surface roughness estimation in a high-speed flat end milling process under wet cutting conditions, using machining variables such as spindle speed, feed rate, depth of cut, and step over. First- and second-order models were developed using experimental results of a rotatable central composite design, and assessed by means of various statistical tests. The highest coefficient of correlation (R_adj²) (88%) was obtained with a 10-parameter second-order model. Meanwhile, a time trend was observed in residual values between model predictions and experimental data, reflecting the probable effect of the tool wear on surface roughness. Thus, in order to enhance the estimation capability of the model, another independent variable was included into the model to account for the effect of the tool wear, and the total operating time of the tool was selected as the most suitable variable for this purpose. By inserting this new variable as a linear term into the model, R_adj² was increased to 94% and a good fit was observed between the model predictions and supplementary experimental data.In this study, it was observed that, the order of significance of the main variables is as X₅>X₃>X₄>X₁>X₂ (total machining time, depth of cut, step over, spindle speed and feed rate, respectively).     

硅烷涂层提升钢纤维-砂浆界面性能的试验研究

为了提升钢纤维-砂浆界面的黏结性能,采用9种基于硅烷的表面处理剂对钢纤维进行浸渍处理并高温固化成膜;埋置于水泥砂浆圆柱体试块中,开展单根纤维拉拔试验,获得拉拔荷载-位移曲线. 试验结果表明,采用不同的硅烷涂层对钢纤维进行表面改性,可以不同程度地改善钢纤维-砂浆界面的黏结性能;拉拔峰值荷载最高增加5.75倍,拉拔能耗最多增加2.48倍. 硅烷Z6011和Z6020及复合涂层能够较大幅度地提升界面黏结强度,主要增加钢纤维与砂浆界面的化学黏结力;硅烷Z6030和Z6040及复合涂层对界面黏结强度的提升幅度相对较小,主要增加界面滑移摩擦力. 采用扫描电子显微镜（SEM）研究界面黏结性能的提升机理,发现硅烷涂层使得界面过渡区的微观结构更致密,显著提升了钢纤维-砂浆之间的黏结性能.     

Experimental determination of gas holdup and volumetric mass transfer coefficient in a jet bubbling reactor

The hydrodynamics and mass transfer characteristics of a lab-scale jet bubbling reactor(JBR) including the gas holdup, volumetric mass transfer coefficient and specific interfacial area were assessed experimentally investigating the influence of temperature, p H and superficial gas velocity. The reactor diameter and height were 11 and 30 cm,respectively. It was equipped with a single sparger, operating at atmospheric pressure, 20 and 40℃, and two p H values of 3 and 6. The height of the liquid was 23 cm, while the superficial gas velocity changed within 0.010–0.040 m·s~(-1) range. Experiments were conducted with pure oxygen as the gas phase and saturated lime solution as the liquid phase. The liquid-side volumetric mass transfer coefficient was determined under unsteady-state oxygen absorption in a saturated lime solution. The gas holdup was calculated based on the liquid height change, while the specific interfacial area was obtained by a physical method based on the bubble size distribution(BSD) in different superficial gas velocities. The results indicated that at the same temperature but different p H, the gas holdup variation was negligible, while the liquid-side volumetric mass transfer coefficient at the p H value of 6 was higher than that at the p H = 3. At a constant p H but different temperatures, the gas holdup and the liquid-side volumetric mass transfer coefficients at 40℃ were higher than that of the same at 20℃. A reasonable and appropriate estimation of the liquid-side volumetric mass transfer coefficient(kla) in a pilot-scale JBR was provided which can be applied to the design and scale-up of JBRs.     

无机盐对新疆油田三元复合驱界面性能影响研究

界面性能对复合驱提高采收率有重大的影响,界面张力越低,洗油效率越高;Zeta电位越高,油水乳状液越稳定。研究了各类无机盐对新疆油田复合驱界面性能的影响。结果显示,Zeta电位的绝对值随着无机盐浓度的增高而增大;无机碱中,碳酸根离子降低界面张力效果最好,氢氧根次之,碳酸氢根最差;阳离子中,钾离子降低界面张力效果最好,其次是钠离子,镁离子会略微提高界面张力,钙离子则会大幅度提高界面张力;阴离子中,与硫酸根相比,氯离子能更好地降低界面张力。通过以上研究,确定了Q站污水处理站外排水更适合三元复合驱配液。     

Influence of radial and axial runouts on surface roughness in face milling with round insert cutting tools

In face milling processes, the surface quality of the machined part depends on many factors, including feed, cutting tool geometry and tool errors. In this work, a numerical model for predicting the surface profile and surface roughness as a function of these factors is presented, incorporating a random values generation algorithm that makes it possible to determine the variation in surface roughness from the values that can be adopted by tool errors. This work is focused on round insert cutting tools and the influence of tool errors such as radial and axial runouts. The results that correspond to a number of teeth equal to 4, insert diameter of 12 mm, depth of cut of 0.5 mm, cutting speed of 120 m/min and feed of 0.4–1.4 mm/rev are analysed. Milling experiments are made to verify the validity of the model and the discrepancies between the experimental and theoretical surface profiles are assumed to be a consequence of different factors such as the variation in undeformed chip thickness along the surface profile.