蒸发冷凝法中气体压强和蒸发温度对粒子大小的影响

在Ｎ＿２气氛中，用蒸发冷凝法，制备了Ｓｎ细微粒和Ｆｅ及Ｆｅ－４７（ｗｔ）％Ｎｉ合金超细微粒。分别用ＳＥＭ和ＴＥＭ，直接观测粒子大小及其分布。结果表明，平均粒径不是随Ｎ＿２气压强增加单调上升，而是在某一压强Ｐ＿（ｍａｘ）下，出现最大值。随蒸发温度提高，Ｐ＿（ｍａｘ）值迅速增大。粒子大小及其分布与粒子生长机制密切相关。对粒子凝聚生长条件进行了简要讨论。     

Dynamic elastic-plastic behaviour of whipping pipes: experiments and theoretical model

This paper is concerned with the problem of pipe whip, the dynamic response of a high pressure piping system subjected to an end force as the result of a pipe break which releases a jet of fluid from the broken section. Both experimental and theoretical results are presented concerning the dynamic elastic-plastic behaviour of cantilever pipes subjected to a transverse force pulse at the free end. Comparisons between experimental data and theoretical predictions are made for mild-steel pipes with outer diameter-to-thickness ratios of 19.5, 28 and 32. It is demonstrated that, for these geometries, the whipping pipes display three characteristically different responses, viz. elastic, plastic hardening behaviour for thick pipes, elastic, plastic hardening-softening behaviour for moderately thick pipes and elastic, plastic hardening-softening-collapse behaviour for thinner pipes. The experimental data taken from a series of high-speed films are compared with the predictions of the instantaneous shapes of the whipping pipes derived from both a rigid, perfectly-plastic, large deflection, dynamic beam model and a more comprehensive model which incorporates the effects of elasticity and plastic hardening and softening, the details of which are presented in the paper.     

武钢 3×10~4m~3/h 空分手动变负荷生产的探索与实践

对武钢引进的两台３×１０４ｍ３／ｈ空分设备，为改变其自动变负荷生产调节范围小、时间长的问题，采用了人工手动变负荷的操作方法。实践表明：扩大了增减产范围，缩短了调节时间，有十分明显的综合经济效益，可供大型空分变负荷生产借鉴参考。     

激光在大型望远镜中应用

简述激光在大型天文望远镜中应用，如激光人造星，测量４．３ｍ主镜面形，自准调校恒星光干涉仪和程差补偿测量，望远镜筒主副镜间相对倾角和弯沉测量等。     

具有厚大断面的大型球墨铸铁铸件的生产

首先通过电炉—LF精炼炉—VD精炼炉—包内球化的工艺路线获得了足够的优质铁液,然后通过选取合适的分型面、设置合理的浇注系统、设计专用的冷铁、安放足够大的保温冒口和上表面加大加工余量来去除夹渣等措施,成功生产了具有厚大断面的大型球墨铸铁铸件。     

A graded diameter and oriented nanorod–thin film structure for solar cell application: a device proposal

This paper presents a device proposal based on a junction between an absorbing semiconductor nanorod structure and another window semiconductor layer for solar cell application. The possibility of band gap tuning by varying the diameter of the nanorods along the length, higher absorption coefficient at nanodimensions, the presence of a strong electrical field at the nanorod-window semiconductor nanojunctions and the carrier confinement in lateral direction are expected to result in enhanced absorption and collection efficiency in the proposed device. Process steps, feasibility, technological tasks needed for the realization of the proposed structure and the novelty of the present structure in comparison to the already reported nanostructured solar cells are also discussed.     

拼接式彩色等离子体大屏幕显示驱动电路的研究

针对拼接结构的高分辨率彩色等离子体大屏幕系统的应用，指出了刷新型电路模式的不足之处，提出了一种混合型模式的驱动电路。从彩色模块ＡＣＰＤＰ的结构特性出发，详细讨论了该电路的工作原理，驱动波形以及放电过程。     

圆锥孔径测量方法与误差分析

圆锥孔径的测量往往比较困难、且精度较低。提出长度测量仪器与环规配合使用,应 用比较测量的方法检测圆锥孔的直径。通过计算和分析可以得出,当被测圆锥孔径不大于180 mm 时,其测量不确定度可小于1.84 μm。给出了测量方法和不确定度计算公式供操作时参考。     

钻井岩屑粒径分布规律的研究

钻井振动筛是固控系统的重要分离设备,其主要任务是清除钻井液中直径大于74μm的固相颗粒。对辽河油田7口井深0～3500m的钻井岩屑进行了实地取样,分析了岩样颗粒直径大于74μm的粒径分布特征。分析结果表明,钻井岩屑具有明显的片状特征,颗粒的粒径分布主要与地层岩性和破岩工具有关,随着井深的变化,其岩样粒径分布呈现出幂分布、2分布和瑞利分布等3组典型规律。给出了岩屑颗粒的概率直径;建议在筛面颗粒运动特性研究、筛网工作载荷的计算和激振方式的选择中,应考虑岩屑颗粒片状特性的影响。     

大系统分解协调在库群防洪优化调度中的应用

文章介绍了大系统分解协调理论,建立了串联、并联库群水库防洪优化调度模型.以澧水流域并联系统为例进行了优化调度计算,并以常规调度方案成果进行了分析比较论证.