LED生产过程中的质量控制

对LED封装过程可能出现的问题逐一指出，并提出解决的办法，着重介绍封装位置对LED发光亮度的影响。以期引起LED封装管理人员及工作人员的注意。     

结构-波浪-海床耦合系统中大圆筒结构的波压力响应

以沉入式大圆筒结构为对象，通过设计随机波浪水槽实验，测取了在单筒和连续筒两种结构型式、两种沉入深度和两种波谱输入下结构表面的动波压力分布。波面高度以及波压力历程均在领域进行分析。通过计算结构表面沿高程和沿环向的波压力谱及波压力传递函数，将单筒实测结果与基于线性绕射理论的解析解进行了比较，同时也详细对比了两种结构型式下的实测结果。文中汇报了在研究中获得的新发现及进行的相应分析，特别是在结构——波浪——海床动力相互作用下对波压力响应机理以及针对连续筒的研究，可为工程应用提供有价值的参考。     

聚四氟乙烯薄膜压敏胶粘带的研制

主要介绍了聚四氟乙烯薄膜和有机硅压敏胶制造压敏胶粘带的方法。     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

变频调速技术在济钢焦化厂高压氨水泵上的应用

济钢焦化厂高压氨水泵变频调速系统采用变频器和PLC相结合的方式 ,具有调速精度高、节能等多种功能 ,保证氨水泵正常工作。全年可增加经济效益 77.3万元。     

FLOW OF NEWTONIAN FLUIDS THROUGH SINUSOID ALLY CONSTRICTED TUBES. NUMERICAL AND EXPERIMENTAL RESULTS

Numerical and experimental predictions of pressure drops in the flow of Newtonian fluids through sinusoidally constricted tubes (SCT) are carried out. The numerical evaluations analyzed in this work are obtained from the following methods: Geometric Iteration (GJM), Geometric Iteration with First and Second Upwinds (GIM1, GIM2), Successive Over Relaxation by Line (SORBLM), Global Galerkin Spectral Method (GGSM), Collocation (CM) and Dufort-Frankel (DFM). The GIM1, GIM2 and SORBLM are applied to SCT and explained in this work. The other methods have been previously reported in the literature with the same purpose. Experiments are accomplished for constrictions of approximately 40,60 and 80% of the average tube diameter and results compare well with numerical predictions of the steady flow. It is concluded that special attention should be given to evaluations of the friction factor ƒ for Reynolds numbers Re between the onsets of flow separation and turbulence due to flow instability. Finally, the SCT as a model for porous media (PM) is discussed.     

脆断事故的原因分析和预防措施

分析高强度材料和大型工程结构元件发生低应力脆性断裂的原因及条件，指出传统强度设计理论的局限性，从设计和工艺上提出防止发生低应力脆断事故的具体措施，给使用高强度材料和设计大型工程结构元件时提供参考。     

A new bubble-point-pressure correlation for the binary LiBr/H2O solution

In accord with the increasing concern about the global environmental issues, the absorption refrigeration heat-pump systems are currently being considered very promising and attractive. For the purpose of supporting the advanced R&D technology in this area, we have developed a novel correlation to represent the bubble-point pressures of LiBr H₂O solutions. The developed correlation covers the most extensive range of validity ever proposed: 273–483 K for temperatures, 0.05 kPa to 1.0 MPa for pressures. and 29 76 wt% LiBr for concentrations.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994. Boulder, Colorado, U.S.A.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.