大中型风力发电机组可靠性研究

研究了大中型风力发电机组的可靠性，讨论了可靠性指标的分配，可靠性设计的四个重要方面、可靠性试验计算机模拟。     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

一种快速中值滤波算法在集装箱检查系统中的应用

讨论了一种新的中值滤波算法，有效地降低了传统中值滤波算法的时间复杂度，提高了计算效率和运算速度。该算法在大型集装箱检查图像处理中的应用，取得了良好的效果，提高了图像处理的速度，增强了图像处理的实时性。     

尾流受扰下复杂体形高层建筑的风压分布特性

本文结合汕头粤东信息大厦的风洞试验,详细分析了复杂结构断面建筑物在其尾流受到下游结构干扰下的风压分布特性。试验表明:处于受扰物体尾流边界上的施扰物体可以降低来流在受扰物体上的分离速度,从而使最大负压系数降低。当施扰物体处于被扰物体尾流边界的某些位置时,被扰物体表面的最大负压系数受到显著影响,最多可降低45%。文中还对典型断面结构进行了进一步的试验研究,在验证以上的结论同时,试验结果也显示,施扰建筑位于被扰结构临近的较大区域,其风压增大15%以上,最大可增大39%。本文所得的一些结论可为相应的工程提供参考。     

粘弹性圆柱壳在轴向恒压下的动力稳定性

基于Timoshenko-Mindlin假设,得到考虑粘弹性的各向同性圆柱壳及纤维增强正交铺设层合圆柱壳在轴向恒压下的动力学方程。文中对两端简支的圆柱壳进行了分析,依Laplace变换,导出动力稳定的特征方程,由Routh-Hurwitz判据建立动力稳定性条件,对两类圆柱壳讨论了横向剪切变形的影响。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

河北省张承地区风沙现状及治理对策

在分析张家口、承德地区风沙形成原因及发展趋势的基础上,提出了河北省防沙治沙工作中存在的问题,根据河北省不同类型区的自然、地理及社会经济条件,提出了风沙治理模式和建议。     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

孔型热轧时轧制力的实用计算公式

采用修正系数法,利用板材在带刻槽的冲头进行深冲与平面冲头下深冲时的接触压力的比值确定孔型影响系数,进而推导出孔型热轧时轧制力的实用计算公式.     

An analytical expression for the power coefficient of an ideal horizontal-axis wind turbine

The paper shows that an analytical evaluation of the power coefficient C_p for an ideal horizontal-axis wind turbine can be made via an expression giving the direct relationship of C_p and the axial induction factor a. The results obtained agree closely with those obtained numerically from the usual integral expression involving several variables.