Effects of Process Conditions on Desalting and Demetalization of Crude Oil

The efficiency of desalting for six crude oils was studied with a SY-1 dynamic simulation experimental installation. The demulsifier DC2 was examined for 1#, 2#, and 4# crude oil and DC4 was used for 3#, 5#, and 6# crude oil. The effects of temperature, electric field gradient, dosage of demulsifier, and washing water on the desalting efficiency of six crude oils were investigated. The results showed that at the optimization process condition after desalting, the desalting efficiency and the salt content of 1# crude oil reached 89.17% and 1.92 mg/L; that of 2# crude oil reached 85.08% and 1.04 mg/L; that of 3# crude oil reached 91.06% and 1.35 mg/L; that of 4# crude oil reached 81.67% and 1.51 mg/L; that of 5# crude oil reached 81.03% and 2.32 mg/L; and that of 6# crude oil reached 86.64% and 2.67 mg/L. Different crude oils have different metal contents. Three assistants, ammonium nitrate (TJ1), nitric acid (TJ3), and polyamine carboxylate (TJ4), were used to improve the efficiencies of desalting and demetalization of six crude oils. TJ4 was more efficient in removing calcium and iron for 1# and 2# crude oil. TJ1 was more efficient in desalting and demetalizing 5# crude oil. The efficiencies for removal of calcium, iron, nickel, and vanadium respectively reached 99.89%, 98.33%, 20.58%, and 43.02%. TJ3 has better efficiency desalting and demetalizing for 6# crude oil. With the concentration of TJ3 increasing from 0 to 80 mg/L, the desalting efficiency increases from 31.22% to 73.54%, and the iron removal efficiency increases from 56.0% to 74.05%.     

点检定修在实际应用中的初步探讨

介绍点检定修在发电厂中的应用，根据十里泉发电厂设备维修的经验提出点检定修向状态检修过渡的方法。     

Polyurethane foams with 1,3‐pyrimidine ring

Attempts of obtaining of polyurethane foams using polyetherols with 1,3‐pyrimidine ring (obtained in reactions of 6‐aminouracil with oxiranes) are reported. Properties of the foams are investigated, especially their thermal stability. The foams show an improved thermal stability up to 200°C for a long time. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal stabilization effect of biphenol monoacrylate on polyamide 6

Biphenol monoacrylate (AL) was combined with a traditional hindered phenolic‐based binary antioxidant system to form a ternary stabilization system for the purpose of further improving the thermal–oxidative stability of polyamide 6 (PA6). The thermal stabilization effect of the antioxidant AL on PA6 was studied in terms of the reduced viscosity, the chemical structure, the yellow index, and the mechanical properties. The results showed that the antioxidant AL, with the proper chemical structure, could improve the thermal stability of PA6 effectively through a unique bifunctional stabilizing mechanism. The interaction of the molecules of PA6 with the antioxidant AL was investigated. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Epoxidation of high trans‐1,4‐polyisoprene and its properties

A new organic‐solvent‐free water‐phase suspension method was used to synthesize partially epoxidized high trans‐1,4‐polyisoprene (TPI) to improve its properties, including oil resistance and wet‐skid resistance. The epoxidation was conducted in an aqueous peracetic acid solution and on the TPI granules prepared by a bulk precipitation method with supported titanium catalyst. The effects of the synthesis conditions, including reaction temperature, reaction time, and pH value, on the epoxy content were investigated. Epoxidized trans‐1,4‐polyisoprene (ETPI) with epoxy contents between 10 and 80% were obtained within 4 h. Both the amorphous and crystalline regions of TPI were epoxidized. The crystallization properties decreased with increasing epoxy content. ETPIs possessed lower mechanical properties than TPI but could be enhanced by vulcanization. The oil resistance and wet‐skid resistance were significantly improved after epoxidation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of post‐treatments on the properties of porous poly(vinyl alcohol) membranes

Porous poly(vinyl alcohol) (PVA) membranes were prepared by a phase‐inversion method. The influence of chemical crosslinking and heat treatments on the swelling degree, resistance to compaction, mechanical strength, and morphology of porous PVA membranes was extensively studied. The crosslinking degree and crystallinity of the membranes, calculated from IR spectra, increased with the treatment time. The porosity, calculated on the basis of swelling experiments, showed a decreasing trend for heat‐treated membranes but remained almost at a constant value for crosslinked membranes. Such a change was further proved with scanning electron microscopy pictures. The behavior was explained by the rearrangement of PVA chains during the heat‐treatment process, which led to morphological changes in the membranes. The mechanical properties of the porous membranes in dry and wet states were measured, and a great difference was observed between crosslinked and heat‐treated membranes in the dry and wet states. The crosslinked membranes showed good mechanical properties in the dry state but became fragile in the wet state. On the contrary, the heat‐treated membranes were more flexible in the wet state than in the dry state. This change was explained by the turnaround of inner stress in the systems during the swelling process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of olive residue benzylation on the thermal and mechanical properties of poly(vinyl chloride)/olive residue composites

The changes in mechanical properties, the thermal stability, and the water absorption capacity of poly (vinyl chloride)/olive residue flour composites were studied as a function of various residue olive flour ratios, i.e., 0, 5, 15, and 25% by weight taking into account the effect of benzylation chemical treatment of the filler. The study showed that composite samples prepared with the untreated filler exhibited higher tensile modulus and hardness compared with the neat resin, whereas elongation and tensile strength were observed to decline. On the other hand, the PVC hardness was found to increase with addition of the untreated olive residue flour (ORF), however the composite samples prepared with the benzylated flour exhibited lower hardness than those prepared with untreated olive residue. Moreover, the amount of absorbed water depends on the amount of filler in the composite. The comparison of the results obtained from the samples of F5, F20, and F30 formulations between the untreated and treated ORF indicated a reduction in absorbed water for the composite samples containing treated ORF with benzyl chloride. As a result, the mechanical properties of the treated composites were improved. Furthermore, the thermal characterization of the different samples carried out by color change test and thermogravimetric analysis revealed an increase in the onset temperatures of decomposition for the treated composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The synthesis of block copolyetherketones based on 4,4′‐dichlorodiphenylketone,phenolphthaleine, and bisphenol A and investigation of their properties

Block structured polyethers based on phenolphthaleine, 4,4′‐dichlorodiphenylketone, and bisphenol A with different degrees condensation (n = 1, 5, 10, and 20) were synthesized by means of acceptor‐catalytic polycondensation. Equaimolar quantities of chloranhydrides of iso‐ and terephthalic acids were used. Higher molecular masses were obtained from longer oligoketones with higher condensation degrees. Better molecular packing, increased thermal and mechanical properties were obtained with higher condensation degrees of oligoketones. © 2007 Wiley Periodicals, Inc. JAppl Polym Sci, 2008     

Computer simulation of the effective double layer occurring on a catalyst surface under electro-chemical promotion conditions

In this work, the structural and energetic properties of two typical catalytic surfaces, Na/Pt(111) and O/Pt(111), are studied by means of quantum mechanical calculations and Monte Carlo Grand Canonical simulations. The simulations were performed with electrostatic potentials at different truncation schemes. In order to elucidate the modification of catalyst surfaces produced by the backspillover of ionic species onto Pt(111), the electrostatic field at the interface due to the electric double layer was also analyzed.