碳化硅晶须双重加热合成的研究

双重加热法是低成本、大批量合成碳化硅晶须的新技术，合成温度低、合成时间短、生成率高。对以炭黑和二氧化硅微粉为原料、用双重加热法合成碳化硅晶须的工艺过程进行了研究。观察了不同合成时间、合成温度和催化剂条件下的碳化硅晶须，揭示出不同工艺参数对合成的碳化硅晶须的产出率，微观形貌、直径和长度范围的影响。结果表明，催化剂的使用可以加快反应速度，提高碳化硅晶须的生成率，合成过程为VLS。实验中初步得到的最佳经济工艺参数为：Fe2O3的用量为2％，合成时间为1．5h，合成温度为1250℃。此时的该工艺条件下碳化硅晶须的生成率可达80％，晶须平均直径为0．6μm，平均长度为30μm。     

刚塑性有限元模拟中体积变化问题处理方法

分析了在塑性有限元分析金属体积成形问题中引起体积变化的原因 ,指出在采用罚函数方法引入体积不可压缩条件的刚塑性有限元模拟中惩罚因子、增量步长、节点调整、网格密度和重划次数等是引起体积变化的主要原因。针对所分析原因 ,在现有的方法基础上提出基于三维有限元的节点调整和体积补偿新方法 ,并在实际模拟中应用 ,得到较好的效果 ,提高了模拟的精度和可信度。     

浅述我国电液锤技术的发展与应用

通过对国外电液锤技术的引述，介绍了目前国内电液锤技术的发展与应用状况，并展望了电液锤发展前景。     

TC2M2δ.5钛板冷热翻边成形极限及非对称化研究

TC2Mδ2.5mm钛板室温圆孔翻边成形试验结果表明,除翻边底孔尺寸小于极限值时在唇口边缘发生破裂的正常失效方式之外,冷翻边卸载后制件还出现凸缘平面翘曲、翻边孔口部椭圆化、唇口边缘高度不一致、壁厚分布不均匀等非对称化现象。600℃高温热翻边成形可以有效地提高成形极限,并消除了凸缘平面翘曲和口部椭圆化,但口部高度差以及壁厚不均等非对称化现象依然存在。本文在给出极限翻边系数的同时,对这种非轴对称化程度进行了定量描述,并给出了理论上的分析与解释。     

平砧锻造的数值模拟──随动坐标能量法

平砧锻造是塑性大变形问题，本文采用随动坐标系跟踪流动质点，利用能量法分步计算质点位移增量、等效应变场等，然后叠加。计算结果得到实验验证。     

What do we mean by “catalytic activity”?

The relative reactivities of the lower alkanes in hydrogenolysis on a Pt/Al₂O₃ catalyst depend on the H₂ pressure used, as do those of a Ru/Al₂O₃ catalyst, pretreated in various ways, for propane hydrogenolysis. Apparent activation energies also vary with H₂ pressure. No single rate measurement adequately represents catalytic activity, which is properly defined as the rateconstant for the slow step.     

几种添加剂对模型石膏性能的影响

研究了N型减水剂、硅溶胶等添加剂对模型石膏凝结时间、强度、吸水率、溶蚀率等性能的影响,并确定了有关性能与添加量之间的关系,得出了最佳添加量。     

Diffusion of additives and plasticizers in poly(vinyl chloride): 4. A programmed temperature technique for the determination of the diffusion parameters of three dialkylphthalates

A programmed temperature technique has been developed for the measurement of the self-diffusion coefficients of additives in polymers. This has been applied to the diffusion of three dialkylphthalate plasticizers in poly(vinyl chloride). Values of the self-diffusion coefficients and the calculated activation energies obtained in this way have been compared with values previously obtained from measurements at constant temperature. It has been shown that the programmed temperature technique gives a very rapid method for the estimation of the activation energy of self-diffusion.     

超声波处理微污染水体技术研究

考察了用超声波降解水中低浓度三氯乙腈、氯代苦味碱、溴苯的动力学，并从工程角度分析了多种污染物共存、自然水体等复杂状态下的可行性。探讨了采用空气鼓泡、不控水温的操作方式。结果表明超声波可以较快地去除复杂水体中的多种有机污染物，氧化可在批式反应器与连续流反应器中进行，高流速可以提高反应器的空间与能量利用效率。     

Effect of surface free energy on the adhesion of biofouling and crystalline fouling

Pipelines and heat exchangers using seawater as coolant suffer from biofouling. Biofouling not only reduces heat transfer performance significantly, but also causes considerable pressure drop, calling for higher pumping requirements. It would be much more desirable if surfaces with an inherently lower stickability for biofouling could be developed. In this paper, a cost-effective autocatalytic graded Ni-Cu-P-PTFE composite coating with corrosion-resistant properties was applied to reduce biofouling formation. The experimental results showed that the surface free energy of the Ni-Cu-P-PTFE coatings, which were altered by changing the PTFE content in the coatings, had a significant influence on the adhesion of microbial and mineral deposits. The Ni-Cu-P-PTFE coatings with defined surface free energy reduced the adhesion of these deposits significantly. The anti-bacterial mechanism of the composite coatings was explained with the extended DLVO theory.