NiTi形状记忆合金激光气体氮化层表面特征

为改善NiTi合金的表面性能，利用2kW连续波Nd：YAG对NiTi合金进行激光气体氮化处理。采用SEM、TEM、XRD、XPS和纳米压痕研究了氮化层的显微组织及表面特征．结果表明：激光气体氮化可以在NiTi合金表面制备连续、无裂纹、厚度为2μm的TiN表面层，该表面层中基本不合有Ni元素且具有很高的硬度，其纳米压痕硬度为29．28GPa．     

VN合金在大规格角钢生产中的应用研究

大规格角钢主要用于铁塔制造和建筑结构中。唐钢过去用16Mn钢生产Q345级别角钢，因供轧化学成分范围较窄，供轧率偏低。通过加入V-Fe合金及VN合金进行微合金化，设计了16Mnv(N)钢种生产角钢，使角钢综合性能有显著提高。分析比较了16Mn、16MnV及16MnV(N)角钢的性能，认为在大规格高强度角钢生产中，用VN合金进行微合金化，其效果是最佳的。     

试论安定性不合格消石灰对柔性路面质量的影响

由于过烧石灰的存在和消解不当等原因，造成消石灰安定性不合格，当石灰稳定类路面结构成型或投入使用后，消石灰中的生石灰颗粒开始吸收周围水分，慢慢消解，消解过程中发生体积膨胀，对路面产生破坏。解决石灰安定性问题对防止公路前修后坏，延长路面使用寿命具有积极的现实意义。     

大规格圆钢质量分析和控制

针对湘钢棒材厂生产大规格圆钢出现的表面质量问题，重点介绍了在成品轧机后采用U形辊道和立活套替换棍道；冷床输入辊道采用镶WT合金套；增设高压水除鳞装置；中间轧件尺寸精度控制等措施，成功的解决了大规格圆钢表面擦伤、“麻面”、尺寸超差等表面质量问题，产品质量显著提高。     

钼酸铵溶液深度净化工艺探索

对传统的钼酸铵溶液净化工艺及文献介绍工艺进行了较为详细的分析 ,并与实验数据对比分析 ,找到了较为合理的工艺方案     

套管钻井用套管外表面磨损后剩余强度分析

在分析讨论套管钻井管柱磨损形态的基础上,结合API5C5实物试验尺寸要求,通过有限元计算分析方法,对钻井套管完钻后含有外表面磨损缺陷的套管柱的极限剩余抗挤强度和极限剩余抗拉强度进行了研究,分别获得了均匀磨损和偏磨条件下,套管钻井套管柱外表面磨损缺陷的临界长度尺寸数值,以及不同破坏失效准则条件下的剩余抗挤强度和剩余抗拉强度的计算方程,为套管钻井中套管柱的设计、计算奠定了理论基础。     

Copper(II) removal from aqueous solutions by fly ash

The removal of Cu(II) by adsorption on fly ash has been found to be concentration, pH and temperature dependent. The kinetics of adsorption indicates the process to be diffusion controlled. The Langmuir constants have been calculated at different temperatures, and the adsorption has been found to be endothermic (ΔH = 15.652 kcal mol^?1). The maximum removal is observed at pH 8.0, and variation in adsorption with pH has been explained on the basis of surface ionisation and complexation.     

硅表面上的纳米量子点的自组织生长

纳米半导体量子点以其所具有的新颖光电性质与输运特性正在受到人们普遍重视。作为制备高质量纳米量子点的工艺技术 ,自组织生长方法倍受材料物理学家的青睐。而如何制备尺寸大小与密度分布可控的纳米量子点更为人们所注目。因为这是关系到纳米量子点最终能否器件实用化的关键。文中以此为主线 ,着重介绍了各种 Si表面 ,如常规表面、氧化表面、台阶表面以及吸附表面上 ,不同纳米量子点的自组织生长及其形成机理 ,并展望了其未来发展前景     

XPS studies of directly fluorinated HDPE: problems and solutions

X-ray photoelectron spectroscopy (XPS) applied to the study of fluorinated polymer surfaces presents several problems related both to peak assignment and to degradation. In this work, we analyse extensively the question of XPS peak assignments in this kind of surfaces. We conclude that in this kind of surfaces using binding energy differences between fluorine and carbon is better than using absolute binding energies. Also a useful relation between fluorine photoelectron energy vs. polymer composition expressed through the atomic ratio fluorine/carbon (F/C) was found. A protocol for data treatment is proposed and applied to a XPS study of the degradation induced by X-ray on high-density polyethylene surfaces modified by direct fluorination. Results obtained for the degradation, namely the atomic ratio F/C obtained by two different methods, combined with angle resolved X-ray photoelectron spectroscopy (ARXPS) were used to study the fluorine concentration profile in depth, producing self-consistent results.