φ114mm直缘成型焊管机组的研制

简介了研制的φ１１４ｍｍ直缘成型焊管机组的技术性能和工艺特点。与普通辊式成型机组相比，该机组工艺先进，焊管精度高。     

新型冷轧(拔)无缝钢管高分子润滑工艺研究

提出了冷轧(拔)无缝钢管高分子润滑工艺。研究了该工艺的PL膜各种特性。介绍了工业实验情况。实验证明,高分子润滑工艺完全满足冷轧(拔)钢管工艺要求,并具有操作简便、环境污染小等优点,完全可以代替传统的磷化-皂化润滑工艺。     

埋地钢管结构设计思路的探讨

主要通过对国内和美国手册关于埋地钢管不同的设计思路进行分析对照,尤其在不同工况、不同土弧包角及砂浆衬砌作用下对钢管壁厚设计的影响进行了探讨,可为其它工程设计提供借鉴。     

高压切割喷嘴冲击磨损的数值分析

以复用矿井含煤颗粒的水对高压切割喷嘴的磨损物理问题为研究对象,采用计算流体力学理论进行数值计算,分析讨论了质量浓度为10、15、20、25、30、40 mg/L条件下速度、剪应力、磨损的分布以及变化关系。计算、分析结果表明:磨损主要发生在出口部位和锥体的后半部份,入口部份和锥体前半部份磨损较小;入口部位、锥体部位磨损量、剪应力随质量浓度增加变化较小;出口部位磨损量在质量浓度为10～20 mg/L减小较快,超过20 mg/L后变化不大;出口部位流体速度、磨损量、剪应力与质量浓度间存在对应关系。煤粒入口速度与混合物速度相同、锥体部位煤粒流体速度低于锥体部位混合物速度(平均值)约79.4%;煤粒出口部位速度随质量浓度的增大而呈现先增加后减小的趋势,速度最大值发生在浓度20 mg/L。     

供水管网中压力真实值的批次平差算法

分析了测压点优化布置的意义及原则,并根据供水周期性,依靠数量有限的测压点压力数据,结合管网的水力计算,利用传统的平差原理,将测压点以外的其它节点压力进行真实性校正,推算出了管网各节点的真实压力值,实现了通过有限测压点数据对管网所有节点压力的全面了解。     

塑料管材自动切割系统中定长切割和接口增厚功能的实现

塑料管材自动切割系统以AT89S52单片机为控制核心,通过DA转换输出对牵引机速度进行控制,实现管材定长切割和切割位置增厚操作。增厚操作有利于管材在扩口时达到规定的厚度,保证管材加工的质量。     

Effect of pressure on three catalytic partial oxidation reactions at millisecond contact times

The effects of pressure on reactant conversion and product selectivities in three catalytic oxidation systems have been examined at pressures between 1 and > 5 atm. Reaction was sustained autothermally near adiabatic operating conditions at temperatures of 1000°C with residence times over the noble metal catalysts between 10^–4 and 10^–2 s. The three systems investigated were (1) HCN synthesis over Pt-10% Rh gauze catalysts, (2) methane oxidation to synthesis gas (CO and H₂) over rhodium-coated monoliths, and (3) ethane conversion to ethylene over platinum-coated monoliths. We find that selectivities in all three reactions do not change dramatically with approximately a five-fold increase in pressure. This strongly suggests that free radical homogeneous chain reactions are not significant in these processes and that they can be operated reliably above atmospheric pressure. For the synthesis of HCN over Pt-10% Rh gauzes, the selectivity to HCN can be maintained above 0.75 at pressures up to 5.5 atm. Selectivities to synthesis gas (CO and H₂) from a methane-air mixture over a Rh-coated foam monolith at pressures up to 5.5 atm were maintained above 0.90. Over a Pt-coated foam monolith, the selectivity to ethylene from ethane-air and ethane-O₂ mixtures was independent of pressure up to 6.5 atm and conversion rose slightly although it was necessary to maintain constant velocity and residence time over the catalyst to avoid carbon formation.This research was supported by DOE under Grant No. DE-FG02-88ER13878.     

Alternating pressure control system for hydraulic robots

Hydraulics is a promising technology for robots. However, traditional hydraulic infrastructures are often large and power-inefficient, with large power sources that hinder mobility. In contrast, electro-hydrostatic actuators are relatively power efficient, but their cost and weight can be excessive in systems with a higher number of degrees of freedom. In this paper, we propose a new alternating pressure control system for hydraulic systems with a higher number of degrees of freedom based on an alternating pressure source system. In this system, the valves open and close in synchronization with a pump with sensor feedback, allowing either pressure or position in each actuator to be controlled independently. With the proposed system, a centralized pump can be used with simplified tubing and simple on–off valves. Moreover, we developed a dynamic duty ratio system that improves performance and reduces pump utilization time. The experimental results confirmed that both the position and pressure of each actuator can be controlled in parallel on a multi-degree-of-freedom system.     

0.618法最优确定盘状摆动凸轮机构的最小基圆半径

在满足机构许用压力角条件下,采用０．６１８法最优确定盘状摆动凸轮机械的最小基圆半径。