天铁炼钢厂四流中间包流场的水模实验及优化

介绍了天铁炼钢厂中间包水模实验原理和过程，分析了斜、直、圆三种型式挡渣墙模拟结果，提出了合理的挡渣控流方案，在生产实践中使用效果良好。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

Experimental Study on Polymer Artificial Bone with HA Coated and Fiber Liners

1Introduction HA(hydroxyapatite)wasakindofbioactiveceram ics,whichhadexcellentbiocompatibilityandtissueaffin ityinthatitscomponentsweresimilartothoseofhuman bone[1].Soitwasthebestknownhumanbonesubstitute,andunprecedentedeffecthadbeenharvestedinrecenttwo d…     

Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.     

多相平衡规律在树脂再生过程中的应用研究

借助于三相平衡体系的性能分析，提出了一步法复苏再生阴离子交换树脂的新思路，从而实现阴离子交换树脂的再生和有机污染去除的同步性．对三相再生体系的再生能力，循环再生能力和树脂的有机污染去除能力进行了研究，并进行了基本性能测试和理论分析．结果表明三相再生体系能够很好的保持再生和循环再生效果，缓解了树脂的有机污染，一步复苏再生法具有理论可行性。     

Water‐Stable,Magnetic Silica–Cobalt/Cobalt Oxide–Silica Multishell Submicrometer Spheres

A method to produce monodisperse magnetic composite spheres with diameters from less than 100 nm to more than 1 μm in water solution is reported. The spheres consist of a dielectric silica core and a cobalt/cobalt oxide shell which can be protected from further oxidation with an outer shell of silica or, alternatively, they can be covered with the polymer polyvinylpyrrolidone as a stabilizer. The formation of a uniform magnetic shell proceeds with the adsorption of metallic cobalt seeds, produced by the reduction of cobalt chloride with sodium borohydride, on a self‐assembled layer of polyelectrolytes on the silica core. In the second step, an outer silica shell can be formed by the hydrolysis and condensation of (3‐aminopropyl)trimethoxysilane and tetraethoxysilane. The double‐shell composite spheres show excellent sphericity, monodispersity, and a magnetic hysteresis loop at room temperature.     

端羟基聚二甲基硅氧烯改性环氧树脂

用羟基封端的聚二甲基硅氧烷改性环氧树脂，得到具有两相结构的改性树脂，其耐热性明显提高．环氧树脂／有机硅（20／80）共混物涂层有很低的表面能，主要的机械性能则变化不大，可作为一种疏水性防护徐层．     

Modelling aerodynamic sound in the airways of a human body: A possible diagnostic tool

The sound generated aerodynamically by a pillow-like body simulating an obstacle in the human airway is observed through a soft wall from outside the duct. It is intended to provide a physical basis for an attempted medical diagnostic technique for detecting an obstacle by observing the sound during breathing. So far at least two kinds of sound have been identified: One is sound of the half-jet flow formed downstream of the obstacle, and the other is sound due to unsteady motion of the separation point on the curved surface of the obstacle. For simulating the flow condition downstream of the vocal cords during inhalation, cases with an obstacle at various positions relative to a jet flow are also examined. In this case, the sound due to the downstream obstacle exhibits a complicated dependence on the geometry and flow parameters. Nevertheless, increase in the sound, or more correctly, deformation in the sound power spectrum, due to the presence of an obstacle is detectable from outside, opening up possibilities of its use as a diagnostic aid. Dedicated to the late Professor Itiro Tani on the occasion of 5ACFM, Taejon, Korea     

激光辐照制备搪瓷涂层

激光辐照制备的搪瓷涂层表面粗糙,与金属基材结合牢固。一般由 Si,Al,Na,K,B,F,O等元素组成。在激光辐照过程中 K,Na 明显地挥发,从而在涂层中的含量明显减少;Co,Ni,主要分布在界面附近;Fe 元素也由基材进入涂层,呈梯度状分布,在界面过渡区含量很高,在涂层内含量很低。搪瓷涂层的形成与激光辐照参数,特别与激光功率间存在极为密切的关系;只有选用合理的参数,才能制得搪瓷涂层。     

防腐涂料及涂装技术(Ⅷ)

防腐涂料及涂装技术讲座系列介绍防腐蚀涂料的品种和各类应用及最新产品研究进展。本讲主要介绍涂装前的表面预处理方法及表面处理质量的评定等