Application of a Compaction Simulator to the Design of a High-Dose Tablet Formulation. Part I

The compaction properties of an investigational drug are studied by the use of a compaction simulator. The effects of punch velocity over the range of 30-640 mm^-1 on the compaction properties of the pure drug and a variety of formulas incorporating a high dose of the active compound have been investigated. The data were analyzed by applying the Heckel equation. The pure drug was found to have a high yield pressure at a relatively low punch velocity of 31 mm^-1. As the punch velocity was increased there was a decrease in crushing strength, primarily as a result of increasing yield pressure. These findings indicate that the pure drug predominantly consolidated by fragmentation and elastic deformation, with a slow plastically deforming component. The information obtained on the consolidation mechanism of the pure drug and, subsequently, on model formulas were instrumental in the design and selection of a robust formula and granulation process. The advantages of conducting dosage form design and characterization studies during the early phase of tablet formulation using means such as a compaction simulator are emphasized in this investigation.     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

High‐pressure processing effects on the mechanical,barrier and mass transfer properties of food packaging flexible structures: a critical review

Food products can be high‐pressure processed (HPP) either in bulk or prepackaged in flexible or semi‐rigid packaging materials. In the latter case the packaging material is subjected, together with the food, to high‐pressure treatment. A number of studies have been performed to quantify the effects of high‐pressure processing on the physical and barrier properties of the packaging material, since the integrity of the package during and after processing is of paramount importance to the safety and quality of the food product. This article reviews the results of published research concerning the effect of HPP on packaging materials. Copyright © 2004 John Wiley & Sons, Ltd.     

α-Fe_2O_3(SO_4~(2-),Sn)气敏电阻的温度响应特性

在气敏温度区域内研究了α-Fe_2O_3(SO_4~(2-),Sn)材料的电阻-温度特性,认为表面结构的变化导致温度特性出现峰值并呈现气敏性。可利用空气中电阻温度特性提供的信息改性或发现新的气敏材料。     

Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

压力容器材料质量控制的几个重要环节

针对压力容器材料方面存在的问题,从设计、采购、检验、制造等环节进行了分析,根据实际情况确定材料的质量控制要点。材料使用前要通过各种检测手段,判断材料的真实性,确保所用材料合格;并应从设计、选材、采购、计划、填报内容和选择可靠的供应方等方面加以控制,确保材料的正确使用,为压力容器产品的材料控制提供借鉴。     

微波高压提取快速测定饲料含氟量的探讨

采用微波高压制样技术,快速提取饲料中的氟元素,结合氟离子选择性电极标准添加和电位极差测试方法,能够快速、准确地测试饲料中的含氟量     

High-Pressure (up to 140 MPa) Dynamic Viscosity of the Methane and Toluene System: Measurements and Comparative Study of Some Representative Models

The dynamic viscosity of toluene and methane mixtures containing 25.03, 37.19, 49.95, 64.11, and 95.00 mol% methane has been measured using a falling-body viscometer. The measurements (280 data points) have been performed in the temperature range 293.15 to 373.15 K and at pressures up to 140 MPa. The data have been discussed in the framework of recent representative models (hard-sphere scheme, friction theory, and free-volume model) as well as with simple mixing laws and empirical models (particularly the LBC model and the self-referencing model) used in the literature. This comparative study shows that the average absolute deviation of the models is between 4.9 and 26.8%, and the maximum deviation is between 11.6 and 49.5%.     

温度,压力对漂移室气体增益的影响

研究了温度及气体压力对漂移室（工作于正比区）气体放大倍数的影响，温度和气体压力的变化范围分别是５￣４０℃及９０￣１０５ｋＰａ。用实验数据拟合得到了函数关系并测量了几种饱和度下函数中的参数值。     

Solid-liquid phase equilibria of benzene + 2-methyl-2-propanol system under high pressures

Solid-liquid phase equilibria of the benzene + 2-methyl-2-propanol system have been investigated at temperatures from 278 to 323 K and pressures up to 300 MPa using a high-pressure optical vessel. The uncertainties of the measurements of temperature, pressure and composition are within ±0.1 K, ±0.5 MPa, and ±0.001 mole fraction, respectively. The freezing pressure at a constant composition increases monotonously with pressure. The eutectic point shifts to a higher temperature and benzene-rich composition with increasing pressure. In order to describe the pressure-temperature-composition relation of high-pressure solid-liquid phase equilibria, a new simple equation has been proposed as follows: