VCM压缩机曲轴断裂失效分析

介绍了锦化化工(集团)有限责任公司出现的VCM压缩机曲轴断裂事故，并从断口的部位、形貌特征，断轴的几何状态、受力状态及树料性能等方面分析了曲轴断裂的根本原因。     

开关磁阻电机传动技术及其应用

本文主要论述了开关磁阻电机传动技术的工作原理，系统结构和技术性能。介绍了该技术的发展背景、目前的应用情况和国内外发展水平。并对其前景表明了一些看法。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

多变量系统故障诊断和容错控制新方法及其在精馏过程中的应用

本文提出一种多变量系统的故障诊断和容错控制新方法，整个系统由四个神经元组成。将本文方法用于二元精馏塔顶和塔底组分的容错控制，仿真结果证实了本文方法的有效性。该方法可望在难以建模的复杂化工过程中得到应用。     

Knowledge-based diagnosis of drill conditions

One major bottleneck in the automation of the drilling process by robots in the aerospace industry is drill condition monitoring. This paper describes a system approach to solve this problem through the advancement of new machine design, sensor instrumentation, metal-cutting research, and intelligent software development. All drill failures can be detected and distinguished: chisel edge wear, flank wear, crater wear, margin wear, corner wear, breakage, asymmetry, lip height difference, and chipping at lips. However, in the real manufacturing environment, different workpiece materials, drill size, drill geometry, drill material, cutting speed, feed rate, etc. will change the criteria for judging the drill condition. The knowledge base used for diagnosing the drill failures requires a huge data bank and prior exhaustive testing. A self-learning scheme is therefore introduced to the machine in order to acquire the threshold history needed for automatic diagnosis by using the same new tool under the same drilling conditions.     

水闸闸室化算梯形横截面上不平衡剪力的分配计算

当地弹性地基梁法计算非岩石地基的水闸底板应力时，首先要求解出不平衡剪力，当闸墩截面选择梯形时（主要是边墩），常用方法是作图法，这既有误差又繁琐。所以就此推导出一个公式，可直接求解平衡剪力。     

精轧油膜轴承密封失效机理的初步分析

对油膜轴承密封出现的进水、漏油现象作了大量的调查、测量和统计分析，找出了产生质量事故的根本原因，提出了解决措施。     

圆杆弹性和弹—塑性扭转公式的探讨

对圆杆在线弹性阶段，弹－塑性阶段和全塑性阶段的扭转剪应力的计算公式作了分析，并推导了在材料的应力－应变关系（τ－γ关系）不服从虎克定律时，扭转真实剪应力的计算公式。文中对扭转强度计算公式的来源，物理含义及其都作了详细的说明。这对执行和理解国家ＧＢ１０１２８－８８《金属室温扭转试验方法》是有益的，而且对高校中材料力学的教学具有一定的参考价值。     

Off-Optimum Cure of Aerospace Epoxy Adhesives

Four epoxy film adhesives used in aircraft manufacture and repair have been examined to establish the effect of deviation from the cure cycle specified by the manufacturer. In addition to the variation of the cure cycle, two surface preparations of the aluminium adherends (chromic acid etch or grit blast followed by silane treatment) were evaluated. Thermal analysis was used to examine the cure envelope of the adhesive, and its extent of cure and glass transition temperature. The adhesive properties were assessed by shear strength (in both single lap joints and in Iosipescu configuration), durability (Boeing wedge test) and chemical resistance to selected aggressive fluids. The sensitivity of the performance of a particular adhesive to offoptimum cure conditions depends on its composition and needs to be determined, not predicted.     

Fault-accommodation with intelligent sensors

Optimal sensor fault-accommodation is considered for faults modelled by an increase in measurement noise. This noise is taken to be bounded and its probabilistic properties unknown. It is assumed that intelligent (e.g. self-validating) instrumentation is in use and estimates of the noise bounds are available. The fault-tolerant controller is designed to optimize a noise rejection and a nominal reference tracking index and leads to a mixed norm minimization problem (l₁/l₂). We exploit known results and a particular feedback configuration to show that it is possible to optimize simultaneously without a trade-off the two performance indices. The results are applied to systems where the presence of auxiliary measurements allows for an optimal fault-accommodation strategy. Using properties of the optimal solution, we define a factorization for the optimal controller alternative to the Youla parametrization, leading to an algorithm which is optimal, transparent and efficient.