特殊混凝土在30000 m3/h制氧机工程中的应用

主要介绍了马钢公司30000 m3/h制氧机工程中冷箱基础珠光砂混凝土的试配、检验与施工。     

龙开口水电站溢流坝段动力模型破坏试验研究

采用仿真混凝土材料研究了龙开口水电站溢流坝段在不同因素影响下的动力破坏特征,并通过对6个模型试验结果的分析探讨了溢流坝段的动力破坏机理。试验中考虑了坝体-库水的动力相互作用以及横河向地震动对大坝破坏的影响,采用规范谱波和场地谱波两种地震动激励进行模型超载破坏分析。试验结果为工程设计和评价溢流坝段的抗震性能提供依据。     

Large-scale cooling towers as part of an efficient and cleaner energy generating technology

The present paper will outline the main aspects of the design and construction of cooling towers in Germany in the last decade. As part of electricity generating power plants, cooling towers play a significant role for the availability of reliable energy supplies, in a manner compatible with environmental requirements. They definitely belong to the largest and thinnest concrete structures at present. Because of the combined action of wind, thermal and moisture effects, special care has to be taken with regard to fatigue, cracking and corrosion to ensure an adequate level of safety and durability. Such a design strategy has been employed for the world’s tallest cooling tower at the Niederaussem power plant in Germany, with an overall height of 200 m and thickness values of 22–24 cm. Special considerations included the realistic non-axisymmetric distribution of soil characteristics, wind action due to interference effects (as determined by wind-tunnel tests), optimisation of the shell shape to improve structural and dynamic behaviour, injection of the cleaned flue-gas into the cooling tower, and the use of high-performance concrete (85 MPa) to improve shell resistance against acid attack by the cleaned flue-gas. The paper will present some results of an actual research project on this problem, which was conducted at the University of Wuppertal, to explore the use of high-performance concrete on design, stability and durability of cooling tower shells.     

PLC在环锭捻线机上的应用

介绍了如何使用PLC和数字变频调速技术 ,对传统环锭捻线机进行技术改造 ,使锭速、捻度和卷绕成形变换实现数字化柔性控制 ,扩大了工艺参数的变化范围 ,使整个捻线加工车间实现信息化管理成为可能。     

钢纤维混凝土轴拉应力-应变特性的试验研究

本文采用环氧粘接法对4种纤维混凝土材料进行了轴向拉伸试验，成功地获得了材料的应力-应变全曲线。根据其试验曲线是否出现第二峰值，把纤维分为增强与增韧两大类。通过分析表明：不同的纤维形式对混凝土材料的作用机理有较大的差异。在工程应用中，应根据纤维混凝土材料的用途来选择纤维类型。     

煤矸石高路堤下多孔拱涵顶进

介绍了国内首例煤矸石高路堤下顶进工程的施工     

Solids Extraction of Cod Frame and Effects on Ultrafiltration of the Aqueous Extract

Grinding, pH adjustment, heat treatment and centrifugation were studied to recover solids from ground cod frames and to apply ultrafiltration (UF) to the resulting aqueous phase. Early heat treatment (90°C/20 min) dissolved collagen into aqueous phase resulting in a very low UF flux. A pH adjustment to 4.5 after grinding (～0.32 cm die), with no heat resulted in efficient separation after centrifuging. UF of the aqueous phase showed an increase in initial flux (23 L/hr m²). However, when the same aqueous material was heated and then centrifuged (1–2% solids removed), UF flux was further increased to 46 L/hr m²and this process gave highest solids recovery (90%).     

合山电厂3个机组主厂房定向爆破拆除

介绍了广西合山电厂 1#～3# 机组主厂房定向爆破设计与施工.该工程不仅规模大、环境十分复杂、工期紧、难度高、风险性极强,最大特点是拆除发电设备与爆破同步进行施工.     

改性玻纤增强尼龙610,1010塑料

研究了采用(准)中粘度级尼龙做基体树脂,加入成核剂改善尼龙的结晶过程,提高结晶速率和初始熔融温度;添加光、热氧稳定剂,防止尼龙在成型加工和使用过程中产生降解与老化,提高塑料制品的质量和减少性能的分散性;采用合理的工艺条件,确保添加剂的均匀分散与减少玻纤的磨损,得到适于军工、航空和机电等领域需要的高性能的受力结构工程塑料。     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.