聚脲基脂及其在电机轴承上的应用

对电机轴承专用聚脲基脂的特点及其在电机轴承上的应用效果进行了分析和探讨。正确使用电机用润滑脂是保证电机正常工作，减少电机故障的关键措施之一。采用电机专用聚脲基脂后，电机轴承工作温度明显下降，电机故障率明显减少。     

福州洪山大桥支座整体更换施工的方法和措施

本文针对国道316线福州洪山大桥支座整体更换工作中所采用的主要施工方法和措施进行介绍,对类似桥梁的养护工作具有指导意义。     

桥梁板式橡胶支座局部脱空设计成因分析

经过对支座转角组合进行的分析,在研究柔性高墩墩顶转角位移计算方法的基础上,提出了更加严密的支座转角验算修正公式,得出修正后的转角验算公式易于应用的结论,对于保证板式橡胶支座在使用过程中不脱空有重要的意义。     

Thermal and thermoelastic properties of fast extrusion furnace (FEF) carbon black loaded SBR vulcanizates

The effect of FEF carbon black as filler on the thermal capacity c, diffusivity a, and thermal conductivity λ, of styrene butadiene rubber (SBR) composites in the temperature range 300–420 K was studied. The filler strongly increases the thermal diffusivity, whilst strongly decreasing the thermal capacity and the thermal conductivity (except at high FEF content ≥80 phr). The influence of the filler on the thermoelastic behaviour of the same composites was also investigated. It was found that the thermoelastic temperature change (ΔT) increased with carbon black concentration as well as the entropy change per unit extension.     

Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.     

An examination of the effect of composite constituent properties on the notched-strength performance of composite materials

The effect of matrix and fiber properties on the strengths and failure processes of notched, continuous-fiber composite specimens has been investigated. Bearing, open and filled hole tension and compression tests were conducted on AS-4/3501-6, IM-8/3501-6, AS-4/APC-2 and IM-8/APC-2 specimens. Failure characteristics of tested specimens were studied by fractographic techniques. Failure progression was tracked by means of incremental loading, radiography and fractographic inspection.     

高应力水平下滚动轴承疲劳寿命试验研究

通过在三种不同的强化负荷下进行深沟球轴承疲劳寿命试验，并与常规试验一组结果对比。结果表明，适当地加大滚动轴承疲劳寿命试验负荷，可以大大缩短试验时间，而疲劳寿命依然服从Ｗｅｉｂｕｌ分布，且与常规试验结果基本一致，同时疲劳破坏的形式仍是表面下萌生裂纹，然后扩展至表面形成剥落。     

浅谈胶条接头与模具设计

简要地介绍了橡胶条常见接头工艺方法、应用特点及模具结构与设计方法。     

Monomer recycling for vulcanized silicone rubbers in the form of cyclosiloxane monomers. Role of acid buffers

The KOH-catalyzed depolymerization of vulcanized silicone rubbers to reproduce cyclosiloxane monomers was studied. First, the depolymerization was carried out in toluene with varying amounts of KOH to find that the yield of monomers first increased and then decreased with the increment of KOH, the highest yield was 65% at the molar ratio KOH/(Si–O) UNITS=0.08. At the molar ratio 0.13 in the absence of solvent, the monomers yield was 46%. However, when an acid buffer such as KH₂PO₄ and KCOOC₆H₄COOH was added after the KOH-catalyzed depolymerization was over, the product yield was increased remarkably to more than 80%.     

�±���������͹��ữ���ֳ�ʩ��������Է���

本文介绍了陕北气区陕35井第一次下光油管(即不带封隔器)酸化的施工情况,并结合该地区的地层压力特征分析了光油管酸化施工的可行性及应用限度。