Graph‐Theory Approach to Eigenvalue Problem of Large Space Structures

The dynamic analysis and control system design of large space structures involve the solution of the large‐dimensional generalized matrix eigenvalue problem. The computational effort involved is proportional to the third power of the dimension of the matrices involved. To minimize the computational time a graph‐theory approach to reduce a matrix to lower‐ordered submatrices is proposed. The matrix‐reduction algorithm uses the Boolean matrices corresponding to the original numerical matrices and, thus, the computational effort to reduce the original matrix is nominal. The computational savings directly depend upon the number of submatrices into which the original matrix is reduced. A free‐free square plate is considered as an example to illustrate the technique. In this example a matrix of 16th order is reduced to three scalars corresponding to three rigid‐body modes, and three matrices of order three and one matrix of order four.     

上海市电话局用户接入网发展状况

上海市电话局用户接入网建设经历了调研、网络规划、启动实施和进一步完善、规范四个怅阶段、现已基本形成了覆盖政府机关、大专院校、医院、商务大楼及高层建筑、新建住宅小区、区级以上图书馆等范围的用户光纤网络，为加快经济建设步伐、满足多层次用户需求、拓展电信新业务打下了坚实基础。     

DETERMINATION OF TOTAL NITROGEN IN BARLEY AND MALT BY COMBUSTION METHOD—COLLABORATIVE TRIAL

A combustion method, relying on the Dumas principle, for the determination of total nitrogen in barley and malt, has been collaboratively tested by the Analysis Committee of the European Brewery Convention. Repeatability, r₉₅, and reproducibility, R₉₅, values were 0.063 and 0.116% of dry matter, respectively, for samples with nitrogen contents in the range 1.23 to 1.86% N of dry matter. There was no significant difference between these values for barley and malt. The Analysis Committee approved the adoption of the combustion method for inclusion in Analytica EBC as an alternative method.     

WTG420铁路罐车用钢的组织结构和力学性能分析

分析了ＷＴＧ４２０铁路罐车用钢的组织结构和力学性能。提出了冶炼与轧制的技术关键，其一，添加稀土元素改善钢中夹杂物；其二，采用控轧控冷使铁素体晶粒细化。     

强度型光纤传感器的信号检测系统

本文阐述了一种可提高强度型光纤传感器测量精度的检测系统。该系统利用同一检测电路交替检测信号、参考通道的输出信号，并将信号、参考两通道的检测结果相除，从而消除了因发光二极管光源波动及检测电路系统不稳定所带来的误差。采用同步相关技术抑制了噪声，提高了输出信噪比。实验证明，当时间常数ＲＣ为０．０５Ｓ时，采用该检测系统可获得优于千分之一的零点稳定性和优于２×１０３的输出信噪比。     

Longitudinal elastic waves in columns due to earthquake motion

An analysis is presented of longitudinal waves in a thin elastic column. Velocity is specified at one end, and the boundary condition at the other end is expressed in terms of a range of effective impedances of an attached structure. Propagation, reflection and interference of the waves are followed by the method of characteristics. Integration of differential equations along characteristics yields the wave-induced stress, which is then applied to problems of earthquake excitation. Numerical examples are given for recorded updown ground motion of the Kobe Earthquake.     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

地震勘探震源药柱技术进展

介绍国内外震源药柱产品现状,着重介绍了湖北凯龙化工集团股份有限公司近期所取得的技术进展,探讨了一些施工设想及地震勘探震源药柱今后可能的发展方向.     

MPC系统模块结构中的流场研究

本研究中,应用Simple数值计算方法开发了求解MPC系统模块结构中二维流场分布的计算软件。为了验证计算结果的精确性,用多普勒测速仪实测了用有机玻璃制成的MPC模块二维模型的流场,模拟计算结果与实测值对比取得了较好的一致性。四种不同流出角的MPC模块平均总压损失计算结果表明,已开发的软件可作为设计低流阻MPC模块的良好工具。