一种新的含水率校正方法

从研究流体流动规律出发,结合模拟井实验结果,建立了多参数、非线性的半理论和半实验含水率校正模型,提出了反映两相滑脱效应的滑动比概念,其计算方法物理意义清晰并具有明确的收敛边界。与模拟井实验结果进行对比,使用平方法降低了含水率校正误差。     

快重离子在石墨中引起表面及体径迹的STM研究

用多种快重离子辐照高定向石墨（HOPG），借助扫描隧道显微镜（STM）系统地研究了表面及体内缺陷，结果表明，离子在表面及解理面上都形成了小丘状的缺陷，且在表面较容易形成，可以用非连续损伤径迹结构来对其进行解释。     

连续激光引起高空中动态靶材破坏的理论计算

本文在文献[1]和[2]的基础上,考虑动态靶目标是受载结构的影响,综合考虑大气吸收、散射、湍流及热畸变效应对激光传输的影响,计算了连续激光引起高空中动态靶目标的破坏阈值。     

曙光油田超稠油井套管损坏的机理和防治

超稠油特殊的油藏特点决定了其生产周期短、注汽频繁、出砂、汽窜、超覆现象严重，以及套管质量等因素的影响，套管损坏较为严重。对曙光油田超稠油井套管损坏的规律和机理进行了研究，并从钻井和完井工艺的完善、套管钢级和射孔工艺的选择、采油生产参数的确定、注汽管柱隔热效果的提高、防治砂工艺等方面，对套管损坏提出了预防措施和对策。并对套管损坏井制定了修复再利用方案。     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

一种基于GE90-30PLC的飞剪自动控制系统

本文介绍了调整线材轧线精轧机前专用于切头的启停式飞剪的自动控制系统。该系统以GE90—30PLC为控制核心，辅以热金属HMD、光电编码器等元件，能很好地完成飞剪的剪切及定位。其中着重阐述了飞剪控制中各个重要参数的计算原理和方法。     

Hemispheric contributions to nonverbal abstract reasoning and problem solving.

Hemispheric involvement in reasoning abilities has been debated for some time, and it remains unclear whether the right hemisphere's involvement in problem solving is modality specific or dependent on the type of spatial reasoning required. In the current study, 2 types of nonverbal reasoning abilities were examined, spatial reasoning and proportional reasoning, in 109 patients with cerebrovascular disease that was confined to either the right or the left hemisphere or was diffuse in nature. Results indicated that no lateralizing effects were present based on type of spatial reasoning. Findings are consistent with the suggestion that higher order cognitive processes involved in nonverbal abstraction and problem solving are not strongly lateralized to the right hemisphere but rather are more generally distributed throughout the cortex. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

在役加氢反应器试验板脆化和氢损伤的测定与研究

充分利用了带主焊缝的役后试板，在国内首次开展回火脆化、氢介质下断裂韧性与疲劳扩展的研究，结果表明，加氢反应器焊缝有明显的脆化表现。同时，核查了反应器开停车升温速度和降温速度规定，以及确定了裂纹允许尺寸的参考数据，为今后安全运行提供了充分的依据。     

Microscopic fatigue processes in a plain-weave glass-fibre composite

This paper focuses on the microscopic damage and progressive failure of a composite reinforced by plain-weave glass cloth under tensile fatigue loading. The fatigue process was divided into three stages like that of multi-directional laminates. It was found that the internal damage at each stage (matrix cracks, debonds in the weft, successive debonds in the warp and ‘metadelaminations’ between warps and wefts) occurred near the cross-over point of the fabric. The modulus decay mechanism was explained by considering the progression of this internal damage. From the end of the first stage to the beginning of the middle stage, a characteristic damage state (CDS) (called a ‘meta-CDS’) was observed. It was found that woven composites have a unit area of damage accumulation (called a ‘unit cell’) and the damage of each unit cell and its distribution control the total fatigue damage of the material.     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。