Bridging process and structure through criteria

Scholars in design face two central challenges in design methods inquiry: firstly, to integrate process and solution, and secondly, to examine developmental junctures leading to innovation. With these goals in mind, we maintain that design criteria deserve greater attention and illustrate this position with a study of noted designers' use of criteria. The primary finding was that five criteria functions were considered during the design process. The study also explored potential relationships between designer variables (i.e., professional expertise and personality type) and criteria use.     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

《燃气红外线辐射供暖系统设计选用及施工安装》国家标准图集介绍

介绍了该国家标准图集的主要内容：设计说明、典型设计、工程实例、系统设备、燃气管道安装、液化石油气气化站、电气控制及温度检测、施工安装说明。     

Effects of temperature, ammonium and glucose concentrations on yeast growth in a model wine system

In enology, alcoholic fermentation is a complex process involving several mechanisms. Slow and incomplete alcoholic fermentation is a chronic problem for the wine industry and factors leading to sluggish and stuck fermentations have been extensively studied and reviewed. The most studied cause of sluggish and stuck fermentation is the nitrogen content limitation. Nevertheless, other factors, such as temperature of fermentation and sugar concentration can affect the growth of yeasts. In this study we modelled the yeast growth‐cycle in wine model system as a function of temperature, sugar and ammonium concentrations; the individual effects and the interaction of these factors were analysed by means of a quadratic response surface methodology. Cell concentrations and weight loss were monitored in the whole wine fermentation process. The results of central composite design show that lower is the availability of nitrogen, higher is the cell growth rate; moreover, initial nitrogen concentration also influences survival time of Saccharomyces cerevisiae.     

Characterizing Performance Variation of Product Designs

Quality and reliability design practitioners have utilized Taguchi's methodology of matrix experimentation to generate computer simulation data for characterizing performance variation of product designs. However, the sampling strategy employed renders computer implementation of matrix experimentation cumbersome and statistically invalid. Weaknesses of this approach also include sample size limitation and overestimation of performance variation. An alternative approach that combines Monte Carlo simulation with the strategies of independent sampling across runs and correlated sampling between runs is presented. An application case study shows that the proposed approach constitutes an improvement on the matrix approach with respect to statistical validity and estimation accuracy.     

锌钾硼对甜菜产质量效应及最佳施肥措施的研究

本文利用最优回归设计“310”方案,研究了黑土地甜菜 Zn、K_2O、B的效果及合理施用问题。得出甜菜块根产量、含糖、产糖量、灰分 K 和有害 N 与 ZnK_2O、B 肥回归关系显著的回归模型,分析了 Zn、K_2O、B 对上述五个指标的效应,明确了 Zn 是影响各项指标的主要因子,并采用频率筛选法,提出了兼顾上述五项指标的优质高产施肥措施。     

Multivariable controller design in an adaptive control scheme

A multivariable control system design approach in the frequency domain is presented. The issue of control system redesign in an adaptive control scheme is discussed. Expert system techniques have been used for the automated design of controllers for multivariable systems. Design knowledge has been represented using rules, facts and objects. The design process consists of a sequence of operations obtained by heuristics and experience in the the design techniques. An automated design session of a multivariable plant using the expert system demonstrates that the expert system appears to work well in its prototype implementation.     

A general variance predictor for Cavalieri slices

A general variance predictor is presented for a Cavalieri design with slices of an arbitrary thickness t ≥ 0. So far, prediction formulae have been available either for measurement functions with smoothness constant q = 0, 1, … , and t ≥ 0, or for fractional q ∈ [0, 1] with t = 0. Because the possibility of using a fractional q adds flexibility to the variance prediction, we have extended the latter for any q ∈ [0, 1] and t ≥ 0. Empirical checks with previously published human brain data suggest an improved performance of the new prediction formula with respect to the hitherto available ones.