矿井串联系统模糊可靠性理论的研究

矿井系统不仅具有随机性，而且同时也具有模糊性，在系统分析与设计过程中应同时考虑这两种不确定性因素的影响。文中提出了模糊故障、模糊功能、系统模糊运营状态和广义可靠度等概念，并在此基础上提出了求单元及串联系统的生产能力、营运费用、应急维修费用、修理时间和广义可靠度等指标的方法，建立了使系统平均生产能力最大的系统最优运营策略的数学模型。     

电信网络管理的望族——TMOS

电信管理及运营支撑是爱立信公司为公用电信网提供的有关管理及运营支撑功能的综合方案，本文介绍了其中的公网管理系统和蜂窝移动网络管理系统。     

Basic concept and decentralized autonomous control of super‐distributed energy systems

New small‐scale dispersed generation systems, such as fuel cells and micro gas turbines, have made remarkable advances lately and they will be applied practically in the near future. Although a large number of researches on the introduction of small‐scale dispersed generation systems have been carried out, only a small number of small‐scale dispersed generation systems are considered in these researches. Therefore, little is known about problems to be solved when a large number of small‐scale dispersed generation systems are introduced into electric power systems. This paper deals with a super‐distributed energy system that consists of a great number of dispersed generation systems such as fuel cells, micro gas turbines, and so on. The behavior of a customer with a dispersed generation system is simulated as the Ising model in statistical mechanics. The necessity of a distribution network in super‐distributed energy systems is discussed based on the Ising model. The feasibility of decentralized autonomous control using vicinity information is also investigated on the basis of stability analysis of the Hopfield neural network model. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 151(1): 43–55, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10368     

SW233 PIN驱动器自动测试系统的研制

介绍了一种集成电路自动测试系统，该系统采用计算机并口作通信接口，用VB6编程，实现了对外围测试电路的控制，用IEEE-488接口卡控制测试仪器，可对SW233电路的36个参数进行自动测试，并将测试结果自动保存在数据库中。该测试系统具有自动化程度高、操作方便、测试结果精确等特点。     

河道堤防老化指标体系评定之浅见

水利工程老化、失修是当前工程不能发挥正常效益的主要原因,建立工程老化指标评价体系是解决该问题的基础工作之一。老化是工程建成后在自然因素和人为活动长期连续的作用下,工程效益衰减、构件功能降低及材料性能逐渐变坏的自然现象。河道堤防以土石为主要材料,应以工程的功能为主建立老化指标体系。依据对工程效益和安全的影响程度,水利工程的综合老化度可分为四级。工程损坏后,在防洪工程运用年度内未能修复称为水利工程失修。解决老化问题主要依靠折旧或大修费,而解决失修问题主要依靠运行管理和维修养护费。     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Expert system for dispatch control in restoration of ehv power system after complete blackout

Present-day power systems operate with high reliability, and it is rare that a blackout will extend over an entire system swiftly and securely. This paper considers automatic power supply to loads after a complete blackout of a system. First, taking into account characteristics of generators, loads, and initial power sources, a method is proposed of allocating several generators to each load in parallel to the system and supplying power to the load sequentially. Second, to remove the imbalance between supply and demand of power, a method is proposed of adjusting the amount of supply and generation according to a present imbalance and the sum of past ones. Third, to automatically issue orders for start-up, parallel, follow-up, stand-by, and stoppage of generators, several rules for each power station are set and an expert system is made based on them. Finally, the expert system is applied to a model power system, and it is verified that it can restore loads without any trouble for a complete blackout which occur at any time of a day and in any restoration pattern.     

Photostabilisation of colour formers for heat-sensitive recording systems: Effect of counter-ions on the photofading of fluoran dyes

Fluorans are given considerable attention as functional dyes for heat-and/or pressure-sensitive recording media. Numerous potential metal complexes were synthesised to prolong the life of coloured species. The protecting effect of these compounds against the photofading was examined on cellulose. It was found that the zinc or nickel salts of 3,5-dihydroxy-2-naphthoic acid and its derivatives can be applied as effective stabilisers against the fading of fluoran dyes.     

Service life planning and performance requirements

Service life planning comprises a model for the determination of a reasonable expected service life for buildings and components, and it establishes a routine for the assessment of design alternatives. A design option is considered reasonable when it meets or exceeds performance requirements over time that have been drawn up specifically for the specific project. Due to this assessment reference, there is a very evident link to the concept of performance-based building. Any stakeholder involved in the value chain or in the design process of the building, as well as regulators and building users, can express performance requirements. Identified requirements, both in relevance and in quality, will vary with the stakeholder and his/her perspective of interest. As building sector manufacturers develop most products with reference to standards rather than with reference to specific requirements, there is no direct link from user requirements to the product design. Instead, the building designer has the responsibility to ensure performance requirements are met by the performance of products integrated into the design. As these design decisions also have to be made at the material and component level, a performance-based building would benefit from an established rationale that enables the communication of performance requirements across the relevant system levels in the relevant design processes. A path for the connection of the established concepts of service life planning and performance-based building is presented. The aim is to identify key elements that need to be developed for the successful linkage of performance-based building with service life planning.