羟基磷灰石涂层人工关节的应用研究

采用人工合成高纯度的羟基磷灰石粉末，喷涂在具有注册证的钛合金和钴铬钼合金人工关节上。通过生物学基础检测、动物实验和临床试用，证明所制作的各种羟基磷灰石涂层人工关节，能诱发骨质生长，起生物固定作用，对治疗丧失功能的骨胳效果甚佳。     

Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

Analysis of the Ductile Strength of Welds Weakened by Notches in Longitudinally Welded Pipes of Large Diameter by the Method of Slip Lines

We study the stressed state of an inhomogeneous welded joint containing an interlayer of a more high-strength material under the action of tensile loads. It is assumed that the contact boundary has a cracklike defect. We deduce analytic dependences of the fracture load on the mechanical inhomogeneity of the joint, thickness of the interlayer, and depth of the defect. The maximum depth of the defect to which the joint is insensitive is established. The proposed theoretical results are innovative and agree with the experimental data obtained for specimens cut out from a pipe of 14KhGS steel.     

Damage mechanism in weldment of 2.25Cr-1Mo steel under creep-fatigue loading

The purpose of this study is to clarify damage process of “Type IV cracking” in weldment of a 2.25Cr-1Mo steel and to propose a micro damage prediction method. From continuous observation under a creep-fatigue test, it was found that spherical shape voids initiated and grew on grain boundaries in fine grain region and these voids grow continuously by changing their shape to crack-like. Both spherical and crack-like void growth rate equations were derived from the proposed void growth model. It was indicated that measured void growth rate under the creep-fatigue loading was well predicted by the growth rate equations.     

The stiffness matrix in elastically articulated rigid-body systems

Discussed in this paper is the Cartesian stiffness matrix, which recently has received special attention within the robotics research community. Stiffness is a fundamental concept in mechanics; its representation in mechanical systems whose potential energy is describable by a finite set of generalized coordinates takes the form of a square matrix that is known to be, moreover, symmetric and positive-definite or, at least, semi-definite. We attempt to elucidate in this paper the notion of “asymmetric stiffness matrices”. In doing so, we show that to qualify for a stiffness matrix, the matrix should be symmetric and either positive semi-definite or positive-definite. We derive the conditions under which a matrix mapping small-amplitude displacement screws into elastic wrenches fails to be symmetric. From the discussion, it should be apparent that the asymmetric matrix thus derived cannot be, properly speaking, a stiffness matrix. The concept is illustrated with an example.     

钻杆接头螺纹退刀尺寸对接头寿命的影响

钻杆接头螺纹退刀尺寸是指外螺纹接头的台肩面到螺纹消失前第一个完整螺纹之间的距离。GB9253．1－88规定退刀尺寸应小于或等于12．7mm内螺纹，钻杆接头内螺纹的锤孔尺寸为16±2mm，以保证内、外螺纹啮合良好。经检测发现，从日本NKK公司进口的所有φ127mm钻杆接头外螺纹退刀尺寸都大于12．7mm，镗孔尺寸为16～18mm。而APISpec7K规定钻杆接头内螺纹最小镗孔尺寸为15．9mm。鉴于此，建议对我国的有关标准作相应修改，与API标准保持一致。     

一种新的机器人手臂控制方法

从机器人手臂的关节电机力学出发，本文提出了一种独立于现行机器人关节控制器的离线补偿方法，通过对－２自由度机器人的数值研究，证明该法不仅能有效地克服由于惯性负载，关节间耦合与重力效应给控制系统带来的动态精度问题，而且还可以消除由于控制系统本身的固有特性所决定的系统的跟踪误差。     

电缆头在线测温系统的应用

统计分析了电缆头故障的概率和故障现象，提出了对电缆头在线测温的必要性，阐述了在线测温系统的特点，使用要点和效果。     

复合沉淀氯化镨钕工艺研究

针对草酸沉淀成本高的问题，提出了复合沉淀的方法，试验结果及生产应用都证明了此方法能达到降耗同效的目的。     

WSP特殊螺纹接头油井管的研制

介绍了WSP特殊螺纹接头的基本结构和设计思想,运用有限元方法,重点论述了密封设计和连接强度设计的方法和准则,并通过全尺寸试验进行了验证。计算和试验结果表明,该接头具有先进的螺纹形式、合理的扭矩台肩和金属/金属密封结构,有效地克服了API圆螺纹和偏梯形螺纹的不足,螺纹达到了与管体等强度,气密封能力达到了管体的内壁屈服压力。研究结果可以为开发更多适合油气田实际的特殊螺纹接头油井管提供参考。