两轴稳定平台大俯仰角状态控制技术研究

在对两轴稳定平台一般构型分析的基础上,指出了其在俯仰方向大角度时稳定控制存在的不足,提出了采用三正交陀螺稳定控制方式解决大俯仰角控制问题的方法,最后利用MATLAB进行了数学仿真,结果表明该方法有效提高了系统的稳定精度。     

The pulse distributed file system

A network of powerful personal computers, linked by a high-speed local area network, is being seen increasingly as an alternative to a traditional centralized time-sharing operating system. The PULSE project is investigating how such a system may be constructed to give the benefits of a self-sufficient personal computer to each user without losing the facilities for communication and sharing of data inherent in centralized systems. In particular, a distributed file system has been built which provides a single global UNIX

1 UNIX is a trademark of Bell Laboratories.

-like hierarchy, with a consistent appearance when accessed from any machine. Replicated copies of files are maintained to improve reliability, increase performance, and enable each machine to run stand-alone, albeit with reduced facilities.     

基于无线网络的制造业物料配送系统的设计*

针对制造业传统物料配送系统存在的缺点,基于业务流程再造的理念,运用无线局域网技术设计了全新的物料配送系统。该系统能够对配送流程进行优化,提高了配送效率,有效地解决了配送不及时所造成的生产速度瓶颈问题。     

露天矿山深-浅耦合台阶爆破方法研究及应用

爆破大块率高一直是困扰国内外众多露天矿山的技术难题,银山矿露天采矿场由于采区地质条件复杂,爆破大块率高的现象尤为明显。为此,针对露天采矿场岩性复杂易产生大块的区域,基于岩石的物理力学性质,计算出千枚岩和斑岩爆破区域需增设的短孔孔位。为减少爆破大块的产生率,提出了中深孔爆破方法—深-浅耦合台阶爆破方法。在银山矿露天采矿场实施深-浅耦合台阶爆破方法后,爆破大块率得到有效控制并取得了显著的社会及经济效益。     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

Silicon Nitride Derived from an Organometallic Polymeric Precursor: Preparation and Characterization

Partially crystalline Si₃N₄, with nanosized crystals and a specific surface area greater than 200 m²/g, is obtained by pyrolysis of a commercially available vinylic polysilane in a stream of anhydrous NH₃ to 1000°C. This polymer does not contain N initially. Crystallization to high-purity α-Si₃N₄ proceeds with additional heating above 1400°C under N₂. The changes in crystallinity, powder morphology, infrared spectra, and elemental compositions, for samples annealed from 1000° to 1600°C under N₂, are consistent with an amorphous-to-crystalline transformation. Although macroscopic consolidation and local densification occur at 1400°C, volatilization and accompanying weight loss limit bulk densification. The effect of temperature on specific surface area is examined and related to the sintering process. These results are applicable to pyrolysis, decomposition, and crystallization studies of ceramics synthesized by polymeric precursor routes.     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

高吸水性树脂的性能及应用

综述了高吸水性树脂的性能及其应用，并预测其广阔的开发前景。     

Experimental Investigation of Epoxy Bonded Polymethylmethacrylate Joints

This paper presents an experimental investigation into various aspects of epoxy-bonded polymethylmethacrylate (PMMA) and PMMA-to-aluminium joints. The effects of adhesive thickness, overlap area, surface roughness, and environmental exposure on the joint strength were studied. Results indicated that the joint strength was not directly proportional to the overlap area, while sanding had a positive effect on the joint strength. A negative effect was observed when adhesive thickness was increased. The fatigue behaviour of adhesively-bonded joints under dynamic loading was found to be independent of frequency, for the range of values tested; however, it was dependent on the test temperature with greater reduction in fatigue life observed in PMMA-to-aluminium joints at higher temperature. Empirical equations from which the fatigue life of joints can be predicted were obtained by regression analysis. Intermittent fatigue testing of the joints was also performed. The epoxy adhesive tested proved to be a satisfactory choice for outdoor exposure. The rate of degradation of the adhesive was slow with the adherend itself degrading at a faster rate than the adhesive or the bondline.