Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

课程群案例嵌入协同教学模式的探索

在课程群的教学中由于每门课程各自独立开展教学,缺乏知识的融合和衔接,导致学生运用综合知识解决问题的能力较弱。在课程群的教学中采用案例嵌入协同教学模式,将完整的工程案例嵌入到课程群各门课程的教学中,协同规划各门课程的教学任务,每门课程再围绕案例展开研究性教学。通过嵌入的工程案例衔接各门课程的知识点,帮助学生建构完整的知识体系,强化工程应用的概念；同时通过研究性教学,培养学生分析问题和解决问题的能力,两部分相结合,提高了学生运用综合知识解决复杂问题的能力。     

平面桁架构建的定日镜面形支撑结构优化及实验

针对反射面成型的复杂影响因素，提出平面桁架构建的定日镜面形支撑结构优化技术路线. 利用模拟仿真、数值计算和优化算法等方法，解析20 m²定日镜面形定义技术路线的4个组成环节：面形规格及宽高比、上弦杆的截面矩、平面桁架组间距的最优值、机加工中工艺控制要点的量化. 试制小型定日镜进行实验，分析光斑形状和能流密度分布特性，并与理想球面形光斑比较，两者的拟合优度大于0.98. 实验结果表明，当反射镜宽高比取1.2，上弦杆截面矩取40 000 mm⁴，桁架组间距取950 mm，上弦杆和斜杆的开孔公差小于0.9 mm时，反射面形的质量提升. 研究从原理和实践上证明了该优化技术路线的可行性.     

新工科理念下“扩频通信技术与应用” 课程教学实践

本文以“扩频通信技术与应用”课程为例，探讨新工科理念下工程学科实践教学改革，具体措施包括：开展虚拟仿真实验，充分发挥双师型教师的主观能动性，开展MATLAB仿真训练、工程技术实训及相关的创新创业训练，结合企业实习以及开展国际交流合作等。     

非测绘专业"测量学"课程的探讨

探讨了非测绘专业中测量学课程教学改革的问题,结合我院实际情况,从教学内容、教材的选用、教学方法、实验实习教学环节等方面进行讨论,希望能起到一定的借鉴作用。     

DISPERSION COMPENSATION CFBG IN100km 10Gbit／s RECIRCULATING SYSTEMS

A 10Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4×167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of±5GHz. At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.     

含氮金刚石结构中Jahn-Teller畸变效应的计算

研究了由J.Bourgoin和M.Lannoo提出的半导体内Jahn-Teller畸变效应的计算理论。应用Bourgoin和Lannoo的方法研究了含中心氮杂质金刚石结构的Jahn-Teller畸变问题,计算了34C+N簇团的T2模耦合沿%111&晶向的Jahn-Teller畸变效应,结果与实验相符。     

开关电源的平均电流自动均流技术

针对多个开关电源并联时易出现负载电流在各模块间分配不均的现象,介绍了常用的负载电流自动均流法——平均电流自动均流法及其工作特性。并针对其存在母线电压降低的缺陷,提出了一种改进的平均电流自动均流方法,经试验证明均流精度比较高。     

He-Ne激光自混合干涉的模式研究

对一般He—Ne激光和频率分裂激光器中偏振态相互垂直的o光和e光的自混合于涉的模式进行了研究，发现了单模变三模的现象，并进行了解释。     

基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。