Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

A unified proposal for characteristic testing methods and figure of merit of 8‐kV/3.5‐kVA class light‐triggered thyristors

Power devices with high capability have been developed. 8‐kV/3.5‐kA‐class light‐triggered thyristors have the highest capability among power devices. These devices are used in the Kii Channel HVDC transmission system in Japan. In this paper, we report the extracted problems of conventional testing methods of 8‐kV/3.5‐kA‐class light‐triggered thyristors among manufacturers, and the proposed unified testing methods on the basis of element characteristics and operating conditions in the Kii Channel HVDC system. Furthermore, we propose a figure of merit for power devices for the practical use, and try to extract elements used at the Kii Channel HVDC system with small margins and low withstand capabilities. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(3): 61–70, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10024     

A stochastic maximum principle for systems with jumps, with applications to finance

We consider a stochastic control problem with linear dynamics with jumps, convex cost criterion, and convex state constraint, in which the control enters the drift, the diffusion, and the jump coefficients. We allow these coefficients to be random, and do not impose any L^p-bounds on the control.

We obtain a stochastic maximum principle for this model that provides both necessary and sufficient conditions of optimality. This is the first version of the stochastic maximum principle that covers the consumption–investment problem in which there are jumps in the price system.     

Upgrading coal-derived liquids to diesel fuel

Distilled fractions of a coal-derived liquid from the H-Coal process were upgraded to diesel fuel by catalytic hydrotreatment. The total hydrotreated products were distilled into naphtha (<180°C) and diesel fuel fractions (>180°C) and the diesel fractions were analysed for hydrocarbon-type composition, hydrogen content and some diesel fuel properties. GC—MS-analyses were carried out on the hydrocarbon-type fractions to identify individual chemical compounds. To investigate the effect of different distillation cut points on diesel fuel yield and properties, cut points for one hydrotreated product were varied. The diesel fuel cetane numbers were correlated with percentage hydrogen, total aromatics and saturates. Cetane numbers above 40 were obtained for diesel fuels containing (i) more than 75% saturates, (ii) less than 15% total aromatics and (iii) a hydrogen content above 12.8%. Compounds identified by GC—MS-analyses (in the diesel fractions) were typical aromatic and cycloparaffin compounds. Normal-and iso-paraffin compounds were not detected. By varying the distillation cut point from 135 to 180°C, the cetane number of the residual diesel fraction improved from 37 to 44. This increase is ascribed to the removal of aromatic compounds in the 135–180°C boiling point range.     

HHD型核子秤电离室物理性能检测

HHD型核子秤电离室已成功地使用于HCS型核子秤.对它的各种物理性能指标进行了检测,各项性能指标都达到了设计要求。     

Lyapunov‐stable discrete‐time model reference adaptive control

Discrete‐time model reference adaptive control (MRAC) is considered with both least squares and projection algorithm parameter identification. For both cases complete Lyapunov proofs are given for stability and convergence. The results extend the approach of Johansson (Int. J. Control 1989; 50 (3):859–869) to include Lyapunov stability for MRAC when the normalized projection algorithm is used for parameter identification. Copyright © 2005 John Wiley & Sons, Ltd.     

DRYING OF GRANULAR PARTICLES IN A MULTISTAGE INCLINED FLUIDIZED BED WITH MECHANICAL VIBRATION

A mathematical model for the drying rate of granular particles in a multistage inclined fluidized bed(IFB) is presented from the standpoint of simultaneous heat and mass transfer, with taking the effect of mechanical vibration added vertically into consideration.

Steady-state distributions for the temperatures and concentrations of the particles and the heating gas, and for the moisture content of the particles are numerically calculated based on the present model. The calculated results show fairly good agreement with the experimental data, which were obtained from the drying experiments of brick particles in a three-stage IFB using comparatively low temperature air(40-60°C) as the heating gas.

It has been found within the range of the experimental conditions employed that, the mechanical vibration added vertically enhances the over-all drying rate of the particles and its effect can be considered equivalent to an increase in the air velocity.     

Thermophysical properties data: Government-university-industry cooperation in multidisciplinary research

Historical developments regarding the realization of the importance of reliable thermophysical properties data in engineering applications are presented. The events leading to the establishment of the Symposium on Thermophysical Properties in 1959 and the accomplishments of the symposia series since then are discussed. Contributions of the National Bureau of Standards to the thermophysical properties field are described.Welcoming address presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.     

Quantitative evaluation of generator power control effect of FACTS controllers for power system stabilization

The advancement of power electronics technologies has significantly developed the power system stabilizing controllers. Quantitative as well as qualitative evaluation of their effectiveness in power systems is a matter of great importance for the feasibility investigation of these apparatus. In this paper, the possible control region of FACTS controllers with series and/or shunt configuration in a single machine to infinite bus system is formulated in the powerangle curve with a set of algebraic equations. The effectiveness of TCPST (Thyristor‐Controlled Phase Shifting Transformer), SSSC (Static Synchronous Series Compensator), and TCSC (Thyristor‐Controlled Series Compensator) for the improvement of the transient stability is evaluated quantitatively as a numerical example. The correctness of the proposed method has been confirmed by analysis based on the electromagnetic transients simulation with a detailed system model. © 2001 Scripta Technica, Electr Eng Jpn, 138(3): 43–51, 2002