胡襄煤田煤层厚度变化特征及其控制因素

根据河南胡襄煤田勘探钻孔资料,对煤层的稳定性和煤厚度变化特征进行研究。研究认为,区内二1煤层可采性指数为0.81,厚度变异系数为39%,属较稳定的全区大部可采的中厚-厚煤层;二2煤层可采性指数为1,厚度变异系数为11%,属稳定的全区可采的中厚-厚煤层;区内煤层厚度呈现东部厚西部薄的分布特征,局部出现无煤带或薄煤带;影响煤厚变化的因素主要为成煤时期地壳的不均匀沉降、成煤后期的古河流冲刷与断裂构造破坏作用。     

Effect of Mg-film thickness on the formation of semiconductor Mg2Si films prepared by resistive thermal evaporation method

Mg fi lms of various thicknesses were deposited on Si(111) substrates at room temperature by resistive thermal evaporation method, and then the Mg/Si samples were annealed at 40 ℃ for 4 h. The effects of Mg fi lm thickness on the formation and structure of Mg2Si fi lms were investigated. The results showed that the crystallization quality of Mg2Si fi lms was strongly infl uenced by the thickness of Mg fi lm. The XRD peak intensity of Mg2Si(220) gradually increased initially and then decreased with increasing Mg fi lm thickness. The XRD peak intensity of Mg2Si(220) reached its maximum when the Mg fi lm of 380 nm was used. The thickness of the Mg2Si fi lm annealed at 400 ℃ for 4 h was approximately 3 times of the Mg fi lm.     

煤层厚度变化区域矿震活动规律研究

为更有效地预防采掘期间深部煤层分叉或厚度变化区域冲击矿压的发生,以某矿回采工作面为工程实践背景,基于矿震活动在能量释放与震动频次方面的变化特征及在空间上的分布规律,分析了煤层分叉及煤层厚度变化对冲击矿压的影响。结果表明:在大能量矿震发生前,日震动频次连续处于高位而日释放能量较长时间维持低水平;在煤层厚度变化区域,矿震活动活跃,容易发生大能量矿震。通过对矿震进行"时间-空间"分析,可以确定矿震集中区域和能量积聚时间段,从而可对煤层厚度变化影响区域进行有针对性的卸压防冲工作。     

优选多地震属性线性回归方法在预测煤层厚度中的应用

采用相关性回归分析和聚类分析优选出三种地震属性：瞬时频率算术平均值、总振幅、总能量。应用线性回归方法建立了瞬时频率算术平均值、总振幅、总能量和煤层厚度之间的回归模型。通过对三元三次回归模型与三元一次、三元二次回归模型预测结果的对比分析,选用三元三次回归模型预测了山西宁武某煤矿的煤层厚度。     

Investigation of thickness and wax content of wax deposits in polyethylene pipe using a flow loop

In this study, the thickness and wax content of wax deposits were found to be thinner and lower in the polyethylene (PE) pipe than in the stainless steel (SS) pipe using a flow loop apparatus. The diffusivity of wax, radial thermal gradient, and wax precipitation rate in the PE and SS pipes were calculated and compared. It was found the diffusivity of wax in the PE pipe was higher and tended to enhance the wax deposition in the PE pipe, while the radial thermal gradient and wax precipitation rate were lower in the PE pipe and had the opposite effects. These factors are shown to be comparable with each other and the effect of the thermal gradient dominates the mass flux of wax from bulk to the oil-deposit interface and into the deposits finally, thus causing differences in thickness and wax content of deposits between the PE and SS pipes.     

MILLING PERFORMANCE OF COATED INSERTS WITH VARIABLE COATING THICKNESS ON THEIR RAKE AND FLANK

During the Physical Vapour Deposition of coatings, the orientation of cemented carbides insert surfaces to the plasma flux direction affects the occurring film thickness distribution on the rake and flank, which in turn might influence the wear propagation in cutting processes. In the present paper the cutting performance in milling of PVD coated cemented carbides inserts with variable film thickness on the rake and flank is introduced and with the aid of FEM-supported calculations explained. The investigation results revealed that a thicker film on the tool rake in comparison to the existing one on the flank and moreover a thick and uniformly deposited film in the cutting wedge region significantly enhances the cutting performance in milling.     

Study on interfacial structure and strength of Si_3N_4/Ti/Cu/Ti/Si_3N_4 PTLP bonding

0IntroductionRecently,the development of bonding technique ofhigh temperature structure ceramic Si3N4becomes a hottopic in the field of ceramic bonding[1].Partial transientliquid phase bonding(PTLP)has been applied in the fieldof high temperature ceramic bonding and made some pro-gress.The selection of interlayer materials is key to PTLPbonding.Since Bender discovered that Ag-based brazingmaterial including Ti could wet ceramic in1954,morestudies have shown that Ti has good wetting prope…     

运用均衡凝固理论解决燃气轮机壳体铸件的缩孔和缩松缺陷

燃气轮机壳体是厚大断面球墨铸铁件,壁厚在80~200mm之间,在生产过程中非常容易出现缩孔和缩松缺陷,运用均衡凝固理论进行工艺改进,充分利用厚壁球铁件的自补缩功能,消除了铸件的缩孔和缩松缺陷,生产验证表明均衡凝固技术作为工艺设计理论和方法,对生产高品质的铸件有普遍意义。     

限动芯棒连轧管机芯棒直径系列的设计方法

分析了通过调节辊缝获得期望的平均壁厚时钢管的横断面特性与辊缝调整量之间的关系，并由此推导出给定壁厚范围时满足某一附加公差率的芯棒直径计算公式。最后结合某西180mm连轧管机组提供的壁厚和芯棒直径系列，对芯棒直径系列的设计和选用方法进行了探讨。     

反差增强剂厚度对磁粉检测缺陷检出率的影响

磁粉检测时,如果磁粉与工件表面的颜色对比度小,则容易造成小缺陷漏检。为了提高磁粉检测时的缺陷检出率,可在工件表面喷涂反差增强剂以提高对比度。试验研究了反差增强剂厚度对缺陷检出率的影响。结果表明:一定厚度的反差增强剂,可以提高对比度,对缺陷检出率的影响很小。