铝阳极氧化膜颜色的检验和观察法

介绍铝及铝合金阳极氧化膜颜色的概念和描写,对颜色的儿种测量方法进行了比较,重点分析观察法及其在各国标准中的异同。在此基础上,提出了GB8013中的对颜色进行观察的条件和理论根据。     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

提高Cr12MoV钢冷作模具寿命的措施

从原材料改锻、预备热处理、淬火及回火、深冷处理、表面强化处理等方面分析介绍了提高Cr12MoV钢冷作模具寿命的一些方法和措施 ,并通过实例表明 ,采用这些方法和措施可较大幅度地提高模具寿命     

Effect of supports on the redox performance of pyrite cinder in chemical looping combustion

Chemical looping combustion (CLC) is a clean and efficient flame-free combustion technology,which combust the fuels by lattice oxygen from a solid oxygen carrier with inherent CO2 capture.The develop-ment of oxygen carriers with low cost and high redox performance is crucial to the whole efficiency of CLC process.As the solid by-product from the sulfuric acid production,pyrite cinder presented excellent redox performance as an oxygen carrier in CLC process.The main components in pyrite cinder are Fe2O3,CaSO4,Al2O3 and SiO2 in which Fe2O3 is the active component to provide lattice oxygen.In order to sys-tematic investigate the functions of supports (CaSO4,Al2O3 and SiO2) in pyrite cinder,three oxygen car-riers (Fe2O3-CaSO4,Fe2O3-Al2O3 and Fe2O3-SiO2) were prepared and evaluated in this study.The results showed that Fe2O3-CaSO4 displayed high redox activity and cycling stability in the multiple redox cycles.However,both Fe2O3-Al2O3 and Fe2O3-SiO2 experienced serious deactivation during redox reactions.It indicated that the inert Fe-Si solid solution (Fe2SiO4) was formed in the spent Fe2O3-SiO2 sample,which decreased the oxygen carrying capacity of this sample.The XPS results showed that the oxygen species on the surface of Fe2O3-CaSO4 could be fully recovered after the 20 redox cycles.It can be concluded that CaSO4 is the key to the high redox activity and cycling stability of pyrite cinder.     

DD—921钢铁常温发黑剂的研制和应用

研究了钢铁常温发黑过程的成膜机理,各组分之间的作用以及相互之间的影响,着重分析了常温发黑的优缺点,工艺控制参数以及经济性。     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

碳纳米管及稀土元素钇(Y)对高Ni含量Ti(C,N)基金属陶瓷组织与性能的影响

研究了不同含量的碳纳米管及0.8%稀土Y对高Ni含量Ti(C,N)基金属陶瓷组织性能的影响.将不同成分的试样分别于1400℃、1410 ℃、1420℃真空烧结,测试抗弯强度、洛氏硬度,观察背散射电子形貌、断口形貌并做能谱分析.结果表明,加入质量分数(下同)为0.8%Y及0.3%～1.0%的碳纳米管时,碳纳米管含量为0.5%的组织较均匀,芯壳结构明显,抗弯强度及硬度均较高.     

萃取预分离法分离富铕中钇矿新工艺

采用一种新的串级萃取方式--萃取预分离法分离富铕中钇矿的新工艺.原料首先流入十几的三出口预先粗分离工艺,其萃余液La～Gd(TbDy)直接流入Nd/Sm工艺;中间出口流入(Gd)Tb～HoY(Er)Gd～Dy/Ho～LuY细分离工艺;出口负载有机相(Ho)Er～LuY流入Gd～Dy/Ho～LuY的洗涤段.结果表明,新工艺的粗分离工艺将占原料约70%的La～Gd(TbDy)预分离掉,使流入Gd～Dy/Ho～LuY工艺的稀土量减少约70%;由于Gd～Dy/Ho～LuY分组的萃余液GdTbDy含Ho2O3小于0.03%,省去原工艺的GdTbDy/HoY分离;新工艺的处理能力提高30%,酸碱消耗减少20%以上,贵重稀土元素Eu和Tb的存槽量大大减少.     

从第八次全国热处理大会看我国热处理技术发展的热点

对第八次全国热处理大会的大会报告和交流论文进行了概述和分析，并就有关我国热处理技术发展的热点问题提出了笔者的一些见解。     

Strengthening technology and mechanism for semi-solid die casting of aluminum alloy

Combined with theoretical evaluation,an optimized strengthening process for the semi-solid die castings of A356 aluminum alloy was obtained by studying the mechanical properties of castings solution treated and aged under different conditions in detail,then,the semi-solid die castings and liquid die castings were heat treated with the optimized process.The results show that the mechanical properties of semi-solid die castings of aluminum alloy are superior to those of the liquid die castings,especially the strengthening degree of heat treated semi-solid die castingsis much greater than that of liquid die castings with the tensile strength more than 330 MPa and the elongation more than 10％,and this is mainly contributed to the non-dendritic and more compact microstructure of semi-solid die castings.The strengthening mechanism of heat treatment for the semi-solid die castings of A356 aluminum alloy is due to the dispersive precipitation of the second phase(Mg2 Si) and formation of GP Zone.