通信性能评估的仿真实验研究

研究了流量控制和差错控制对通信性能的综合影响，着重分析了停止-等待协议和连续ARQ协议的优缺点，讨论了信道利用率和帧长的关系。介绍了几种多点接人技术的基本原理，如CSMA和CSMA／CD，并给出了各自相应的性能仿真曲线。所设计的通信性能评估实验，仿真界面形象丰富，与实验知识点紧密结合，可以大大提高实验教学的效率和质量。     

Estimation and Optimization of the Principal H-Maser Parameters

The scale along the coordinate axes in the equations of motion hitherto used for an H-maser (in relative units) is shown to depend on Q as the quality factor for an H-maser. This hinders both analysis of the operation of the H-maser and optimization of its parameters. The modified equations of motion proposed here do not have that shortcoming. We determine the atomic flux into the bulb that gives the H-maser the best metrological characteristics.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

热流法计算高温炉内辐射传热

高温炉内的辐射传热是工业生产中常遇到的问题。过去，人们在应用热流法计算辐射传热时遇到了一定的困难，使计算结果与实际有一定的偏差。本文运用文献［１］中给出的新热流数学模型，开发出由新热流方程与能量方程相耦合的计算机程序，其中的比热流参数由线加热热源情况下计算得到。用该程序计算了实验室用马弗炉内的温度场，并且用热电偶实测了炉内的一些温度值，理论计算与实测值符合很好。     

Sediment chemistry and nutrient influx in a hydrologically restored bottomland hardwood forest in Midwestern USA

Exchanges of total N and C between a river and its floodplain forest have been enhanced by sedimentation processes during flood pulses at a 5‐ha bottomland hardwood forest located at the Olentangy River Wetland Research Park in central Ohio. In the spring of 2000, the forest was hydrologically restored by notching an artificial levee that had separated the Olentangy River and its floodplain forest for 100 years. One‐hundred flat sediment traps (30 cm × 30 cm) were used to collect sediment samples during spring/summer flooding events from 2003 to 2005. Results showed that sediment deposition is determined by the landscape variability during flooding events, Net sediment deposit in the wettest area averaged 134 ± 12 g‐dry wt m^?2 in 2003, 127 ± 17 g‐dry wt m^?2 in 2004 and 149 ± 23 g‐dry wt m^?2 in 2005. Total N and C sedimentation ranged from 0.49 to 0.92 g‐N m^?2 and 5.2 to 19.9 g‐C m^?2. Fe dominates the sediment chemistry and results show the elemental abundance in the order of Al > Fe > Ca > K > Mg > S > P > Na > Mn > Zn > B > Cu > Mo. A hydrologic pulsing index (HPI) could be used as an indicator for mass changes of energies with hydrologic pulsing events. Restoration of seasonally flooded bottomland forests could stimulate potentially large nutrient and Fe releases, which would eventually lead to an enhanced forest productivity and biodiversity. Copyright © 2007 John Wiley & Sons, Ltd.     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

变压器有载合闸过程中故障分闸后铁心剩磁分析

通过有载合闸变压器模型,分析了变压器有载合闸过程中由于副边突然短路导致主保护动作时电流和磁通的暂态过程,并对变压器铁心内的剩磁作了定性的分析。