非标准工况下空分设备增产氩的研究与实践

文章对非标准工况下的空分设备增产氩措施进行了研究。以宝钢6#60000m3/h空分设备为例,通过设计型算法和校核型算法,建立了空分设备精馏的数学模型,通过改变数学模型的参数,分析了在非标准工况下精馏塔内的组分浓度分布,并提出了优化后的操作方案和操作参数,实施后提高了空分设备的氩提取率,取得了显著的经济效益。     

40000m~3/h空分设备主换热器的设计及制造

通过对进口 4 0 0 0 0m3 /h空分设备主换热器进行结构分析及对比模拟计算 ,用国产传热翅片进行设计、采用真空钎焊工艺制造的主换热器 ,经并网运行 ,设计指标优于原空分设备 ,为今后成套大型空分设备板翅式换热器国产化设计、制造创造了条件。     

离心式空压机轴承技术改造

针对离心式空压机各级轴振动值超标的现象进行技术攻关,解决了制约装置安全平稳生产的瓶颈问题。     

漫谈钢铁企业用空分装置的流程选择

钢铁企业的氧气厂要深入了解本企业的用氧情况及周边市场的需要，据此确定拟新增空分装置的设计参数，选定最适宜的空分流程。探讨了空分流程选择时要考虑的几个方面。介绍了一种对空分装置的投资和长期运行费用之间进行经济性分析的定量计算公式，并得出了四点结论。     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.     

燃气红外线辐射器的节能与环保特性分析

论述了燃气红外线辐射器的基本原理 ,对其节能与环保特性的分析表明 :与大气式燃烧器相比 ,红外线辐射器的燃料节约率为 15 %～ 45 % ,CO2 排放量减少率为 15 %～ 48% ,CO排放量减少率为 96.2 %～ 97.7% ,NOx 减少率为 94.9%～ 96.9% ,具有显著的节能与环保效果     

An investigation of the unstable region for dense phase conveying in sliding bed flow

For fine powdered materials, capable of being conveyed in dense phase, a conveying region exists in which instability in flow and pipeline blockage can occur if the pressure gradient available is insufficient to maintain a minimum value of solids loading ratio. A reduction in material flow rate can also lead to pipeline blockage in this region. Conveying trials under-taken with cement are used to illustrate the nature of the problem.     

稀土元素的分离技术

对目前稀土元素分离过程中几种常用的分离技术进行了综述，使用得较多的仍然是溶剂萃取法和离子交换法，而且新方法也在不断地出现。     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

含氮化合物废气选择性催化氧化技术研究进展

通过对当前含氮化合物废气治理技术的对比分析,总结选择性催化氧化的相关技术优势。根据对含氮化合物的种类及来源分析,介绍氨气、腈类、胺类及其他含氮化合物的催化净化技术。重点总结催化剂的种类、研发进展和在实际使用中可能遇到的问题,同时展望含氮化合物废气选择性催化氧化技术的研发方向。