Cr^3＋=Al2（WO4）3晶体生长助熔剂体系的研究

本文用DTA和XRD法研究了Na_2O-Al_2O_3-WO_3三元系中的Al_2(WO_4)_3-Na_2WO_4截面的相平衡关系。在这截面中发现一新化合物AlNa_3(WO_4)_2。以45mol％Na_2WO_4为助熔剂生长了Cr~(3+):Al_2(WO_4)_3晶体。     

Structural significance of the alkyl substituent at the C-4 of (+)-trans-verbenyl acetate in sex pheromonal activity of the American cockroach

The significance of the alkyl group at the C-4 of (+)-trans-verbenyl acetate, which is the sex pheromone mimic of the American cockroach, was investigated. Seven alcohols possessing an ethyl, propyl, or dimethyl group at this position of the 6,6-dimethylbicyclo[3.1.1]heptane skeleton were synthesized and evaluated by behavioral assay. All of the alcohols were inactive, while three of four acetates of the 2-alcohols induced sexual behavior in male cockroaches at the 0.02 or 0.5 mg dosage level, either of which is many orders of magnitude higher than the threshold level of the natural sex pheromones (10^–8 mg). Among the acetates, the compounds with a methyl group or an -oriented ethyl group at C-4 showed the highest activity. The results are discussed in terms of spatial requirements of the molecules for interactions with the receptor.Studies on the sex pheromone mimic of the American cockroach, (+)-trans-verbenyl acetate. Part VIII. For Part VII, seeComp. Biochem. Physiol.,70A: 229–234 (1981).     

Enhanced Photocatalytic Hydrogen Evolution Over CaTi1−x Zr x O3 Composites Synthesized by Polymerized Complex Method

The solid solution of CaTi_1−x Zr _x O₃ (x = 0–0.15) was successfully synthesized by the polymerized complex (PC) method. This study has exhibited the advantage of the PC method to prepare a highly active CaTiO₃ compared with the conventional solid-state reaction (SSR) method. More importantly, further improvement in phase purity and large surface area was achieved by the doping of Zr⁴⁺, leading to remarkable enhancement of photocatalytic activities compared to pure CaTiO₃. The quantum yield for H₂ evolution over the most active photocatalyst, Pt (1.0 wt%)/CaTi_0.93Zr_0.07O₃, was 1.91% and 13.3% in photoreactions from pure water and aqueous ethanol solution, respectively for 0.1 g photocatalyst, which was about 3.3 and 2.5 times compared to that of PC-derived CaTiO₃.     

基于TD-SCDMA的视频码率动态调整策略

通过对基于TD-SCDMA无线视频监控系统的研究,提出了一种无线传输环境下的视频码率动态调整策略。针对TD-SCDMA信道低带宽、高时延、高误码率的特征,该策略可以根据实时网络环境动态调整码率,以便视频数据能够适应其传输。经过TD-SCDMA无线视频系统的实际应用,证明本策略能够有效解决由于TD-SCDMA信道特征给视频传输带来的不利影响。     

表面处理对氮化硅陶瓷力学性能的影响

采用X射线衍射应力分析的sin2ψ法计算了Si3N4陶瓷试样的残余应力，并分别测量了表面处理前后Si3N4试样的力学性能。结果表明，经平面磨削后的Si3N4试样表面残余应力为拉应力，而抛光处理可适当降低残余应力。两种方法都使试样抗弯强度降低。     

Maximization of total surface area of Pt-SnO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst by the Taguchi method

The maximization of the total surface area of Pt-SnO₂/Al₂O₃ catalyst was studied by using the Taguchi method of experimental design. The catalysts were prepared by sol-gel method. The effects of HNO₃, H₂O and aluminum nitrate concentrations and the stirring rate on the total surface area were studied at three levels of each. L₉ orthogonal array leading nine experiments was used in the experimental design. The parameter levels that give maximum total surface area were determined and experimentally verified. In the range of conditions studied it was found that, medium levels of HNO₃ and H₂O concentration and lower levels of aluminum nitrate concentration and stirring rate maximize the total surface area.     

Study on the polymerization of ϵ‐caprolactam in the interlamellar spaces of [TEACOOH]–montmorillonite intercalations complex and its characterization

The polymerization of ?‐caprolactam between the interlamellar spaces of the [TEACOOH]–montmorillonite intercalations complex was attempted using Na–montmorillonite and 10‐carboxy‐n‐decyltriethylammonium bromide to achieve [TEACOOH]–polycaprolactam–montmorillonite, in which montmorillonite (inorganic polymer) is chemically bonded with the polycaprolactam (organic polymer). The results of X‐ray and IR analysis for the samples obtained after polymerization showed that the polymerization reaction has been successfully accomplished. For the purpose of studying the polymeric reaction product more precisely, we have isolated the polymerized product from the silicate layers and analyzed it with X‐ray diffractometer and IR spectrometer. Comparison of the results of X‐ray and IR analysis between the isolated polymer and the polymer that was synthesized by the reaction of ?‐caprolactam only with the organic cation without montmorillonite showed that both obtained polymers are the same compounds. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1904–1910, 2003     

氮化硅基陶瓷连接技术的研究进展

陶瓷连接技术是结构陶瓷实用化的有效手段，焊料成分对连接体的性能具有决定性作用。本文主要从焊料成分选择的角度，总结了氮化硅基陶瓷连接技术的发展现状；并重点讨论了陶瓷／玻璃复合焊料在β-Sialon陶瓷连接中的应用。     

AC/MMA接枝改性天然胶乳的制备及性能研究

以丙烯基氯（AC）和甲基丙烯酸甲酯（MMA）接技改性天然胶乳，采用正交试验方法研究引发剂用量，反应温度，单体配比，胶乳浓度等对接枝聚合反应中单体转化率和接枝率的影响，测试了改性天然胶乳的粘度，粘接性能及其硫化胶膜的力学性能，耐溶剂性和阻燃性，结果表明，适宜的接枝聚合反应条件为：引发剂异丙苯过氧化氢（CHP）和四乙烯五胺（TEP）的质量分数分别为0．58％和0．36％－0．72％（占橡胶质量的百分率）、反应温度为30℃、单体体积配比v（MMA）：v(AC）＝1．5：1、胶乳质量分数为53．3％，所得接枝胶乳粘度较高，粘结性能较好，耐溶剂性能剂，且有较好阻燃性。     

基于CAD/CAE/CAM/RP的复杂陶瓷产品快速制造技术

针对目前手工方式的卫生洁具等复杂陶瓷产品的研发过程,借鉴CAD/CAE/CAM/RP技术在其它制造行业中应用的成功经验,将这些先进制造技术应用于卫生洁具等复杂陶瓷产品的研发中;CAD用于设计产品和模具的模型,CAE用于模拟洁具冲水过程和分析冲水性能,RP用于制作洁具产品的原型,CAM用于加工试用石膏工作模具。就这些技术的应用提出了两种主要方案,并分析了各自的特点。经过实际应用表明:先进制造技术的应用能大大缩短产品研发周期、提高产品质量、降低开发成本。