Correlation of morphology and barrier properties of thin microwave plasma polymer films on metal substrate

The barrier properties of thin model organosilicon plasma polymers layers on iron are characterised by means of electrochemical impedance spectroscopy (EIS). Tailored thin plasma polymers of controlled morphology and chemical composition were deposited from a microwave discharge. By the analysis of the obtained impedance diagrams, the evolution of the water uptake ?, coating resistance and polymer capacitance with immersion time were monitored and the diffusion coefficients of the water through the films were calculated. The impedance data correlated well with the chemical structure and morphology of the plasma polymer films with a thickness of less than 100 nm. The composition of the films were determined by means of infrared reflection absorption spectroscopy (IRRAS), X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The morphology of the plasma polymer surface and the interface between the plasma polymer and the metal were characterised using atomic force microscopy (AFM). It could be shown that, at higher pressure, the film roughness increases which is probably due to the adsorption of plasma polymer nanoparticles formed in the plasma bulk and the faster film growth. This leads to voids with a size of a few tens of nanometers at the polymer/metal interface. The film roughness increases from the interface to the outer surface of the film. By lowering the pressure and thereby slowing the deposition rate, the plasma polymers perfectly imitate the substrate topography and lead to an excellent blocking of the metal surface. Moreover, the ratio of siloxane bonds to methyl-silyl groups increases which implies that the crosslink density is higher at lower deposition rate. The EIS data consistently showed higher coating resistance as well as lower interfacial capacitance values and a better stability over time for the film deposited at slower pressure. The diffusion coefficient of water in thin and ultra-thin plasma polymer films could be quantified for the smooth films. The measurements show that the quantitative evaluation of the electrochemical impedance data requires a detailed understanding of the film morphology and chemical composition. In addition, the measured diffusion coefficient of about 1.5×10⁻¹⁴ cm² s⁻¹ shows that plasma polymers can act as corrosion resistant barrier layers at polymer/metal interfaces.     

Iron Behavior in the Ozonation and Filtration of Groundwater

In Finnish groundwater, the main substances that require treatment are iron and manganese. In addition to this, groundwaters are soft and acidic. Iron removal is usually relatively effective by oxidizing dissolved iron into an insoluble form, either by aeration or chemical oxidization and removing the formed precipitate by sand filtration. Sometimes, if the untreated water contains high amounts of organic matter, problems may arise for iron removal. In Finland, it is quite common that groundwater contains high levels of both iron and natural organic matter, mainly as humic substances. The groundwater of the Kukkala intake plant in Liminka has been found to be problematic, due to its high level of natural organic matter. This research studied the removal of iron from this water by means of oxidation with ozone and filtration. While the oxidation of iron by ozone was rapid, the precipitate particles formed were small, and thus could not be removed by sand and anthracite filtration, and the iron residue in the treated water was more than 2 mgL^?1. And while the filtration was able to remove iron well without the feed of ozone, the iron residue in the treated water was only 0.30 mgL^?1. In this case, iron was led to the filter in a bivalent dissolved form. So, the result of iron removal was the best when the sand/anthracite filter functioned largely as an adsorption filter.     

Methanol Selective Oxidation to Formaldehyde over Iron-Molybdate Catalysts

This review deals with the important industrial reaction of formaldehyde manufacture by methanol oxidation over iron molybdate catalysts. Detailed reference is made to the used catalyst, preparation techniques (coprecipitation, sol-gel like, mechanical mixing, etc.) including unsupported and supported catalysts, promoters and characterization methods. The controversial active phase assignment (stoichiometric versus Mo rich iron molybdate) is discussed. The proposed reaction mechanisms and kinetic laws for the main and side reactions are examined. The catalyst deactivation processes are reviewed and the role of Mo excess on these processes is underlined. Finally conclusions and perspectives are presented.     

CO hydrogenation over potassium-promoted Fe/carbon catalysts

The effects of potassium on the catalytic behavior in CO hydrogenation over K-promoted Fe/carbon catalysts having low K/Fe ratios were investigated. Even though the doses of potassium were low the promotional effects were pronounced, especially on the olefin-to-paraffin ratio, and theC ₃ toC ₄ olefin selectivities of the K-promoted catalysts were as high as 51 to 66 mol%. Over the catalysts having no or low potassium content the olefin-to-paraffin ratio and the ratio of the CO₂ formation rate to the rate of CO conversion to hydrocarbons remained roughly the same regardless of temperature, while over the K-promoted catalysts having higher potassium content they increased with temperature. Formation of significant amounts of filamentous carbon was observed in the K-promoted catalysts; however, the carbon deposition did not appear to affect the inherent activity and selectivity of the K-promoted catalysts.     

A porous mixed-valent iron MOF exhibiting the acs net: Synthesis, characterization and sorption behavior of Fe3O(F4BDC)3(H2O)3·(DMF)3.5

A new mixed-valent iron MOF, formulated as Fe₃O(F₄BDC)₃(H₂O)₃·(DMF)_3.5 (1), has been synthesized by using a perfluorinated linear dicarboxylate to link trigonal prismatic Fe₃(μ³-O)(O₂C–)₆ clusters. The structure refinement based on single crystal X-ray diffraction data collected from 1 reveals the material exhibits the acs topology with large channels along the crystallographic c-axis. Due to the presence of fluorine atoms the organic link, 2,3,5,6-tetrafluorobenzene-1,4-dicarboxylate (F₄BDC), has a 63° torsion angle between the carboxylate and aromatic planes, resulting in larger channels compared to those in the isoreticular material MOF-235. While few iron-based MOFs have demonstrated porosity, nitrogen and hydrogen sorption experiments carried out at 77 K proved the porosity of outgassed 1, which has a Langmuir surface are of 635 m²/g and a gravimetric capacity of 0.9 wt% of hydrogen at 1 bar.     

Electrocatalyst materials for fuel cells based on the polyoxometalates—K7 or H7[(P2W17O61)Fe(H2O)] and Na12 or H12[(P2W15O56)2Fe4(H2O)2]

Free acids of the iron substituted heteropoly acids (HPA), H₇[(P₂W₁₇O₆₁)Fe^III(H₂O)] (HFe1) and H₁₈[(P₂W₁₅O₅₆)₂Fe^III₂(H₂O)₂] (HFe2) were prepared from the salts K₇[(P₂W₁₇O₆₁)Fe^III(H₂O)] (KFe1) and Na₁₂[(P₂W₁₅O₅₆)₂Fe^III₄(H₂O)₂] (NaFe4), respectively. The iron-substituted HPA were adsorbed on to XC-72 carbon based GDLs to form HPA doped GDEs after water washing with HPA loadings of ca. 1 μmol. The HPA was detected throughout the GDL by EDX. Solution electrochemistry of the free acids are reported for the first time in sulfate buffer, pH 1-3. The hydrogen oxidation reaction was catalyzed by KFe1 at 0.33 V, with an exchange current density of 38 mA/cm². Moderate activity for the oxygen reduction reaction was observed for the iron substituted HPA, which was dramatically improved by selectively removing oxygen atoms from the HPA by cycling the fuel cell cathode under N₂ followed by reoxidation to give a restructured oxide catalyst. The nanostructured oxide achieved an OCV of 0.7 V with a Tafel slope of 115 mV/decade. Cycling the same catalysts in oxygen resulted in an improved catalyst/ionomer/carbon configuration with a slightly higher Tafel slope, 128 mV/decade but a respectable current density of 100 mA/cm² at 0.2 V.     

科技创新与钢铁科技进步

建设创新型国家是我们中华民族的历史责任。“自主创新、重点突破、支撑发展、引领未来”的16字方针应当成为我们未来创新活动的指南。建设创新型国家把自主创新放在首位,并提出了引领未来的高标准要求。钢铁科技创新必须突出重点,抓住创新成果产业化这个关键,支撑起行业和国民经济的发展。     

Mechanistic peculiarities of the N2O reduction by CH4 over Fe-silicalite

Transient isotopic studies in the temporal analysis of products (TAP) reactor evidenced the importance of the lifetime of oxygen species generated upon N₂O decomposition on extraframework iron sites of Fe-silicalite for methane oxidation at 723 K. Fe-silicalite effectively activates CH₄ when N₂O and CH₄ are pulsed together in the reactor. However, these oxygen species gradually become inactive for methane oxidation as the time delay between the N₂O and CH₄ pulses is increased from 0 to 2 s.     

改进灰色模型在中长期电力负荷预测中的应用

针对中长期电力系统负荷预测,在前人已有成果的基础之上,对普通灰色模型进行了改进.一方面对历史数据进行二次平滑处理,大大消除了干扰因素;另一方面利用带有马尔可夫链符号估计的残差修正技术对未来残差的符号进行预测以修正灰色模型的预测结果.以某地区多年以来的历史数据为基础,建立了数学模型,通过实际数据计算表明:改进后的灰色负荷预测方法可以应用于电力系统中长期负荷预测,而且较普通灰色预测模型在预测精度上有着明显的提高,尤其是对于较远时间的负荷预测有着较为理想的预测精度,表明了该种方法的有效性和实用性.     

基于灰靶理论的城市应急供水方案评价研究

针对城市应急供水方案选择面临的多目标评价问题,从水量、水质、工程难度、工程投资等方面建立城市应急供水方案评价指标体系,运用灰靶理论,通过建立标准模式、灰靶变换、构建灰关联差异信息空间、计算灰关联系数和靶心系数,逐层次识别模式接近靶心度的程度,从而对方案进行评价及排序,最终选定方案6作为德阳市应急供水方案,为德阳市灾后重建城市供水提供了重要的科学依据.该方法适合处理信息不完全、少数据不确定性问题更简洁、高效、可行.