一种新型均速管流量计在高炉煤气测量中的应用

高炉煤气具有管径大、流速低、粉尘大、易堵塞等特点，其流量用常规装置测量效果不尽理想。近来，一种新型均速管流量计——威力巴流量计采用独特的结构设计，在高炉煤气流量测量中取得了不少进展。本文对威力巴流量计的基本原理和应用于高炉煤气测量的突出优点进行了分析，并给出了安装使用时的一些建议。     

TMS320F240串口通信特征及其应用

主要论述了TMS320F240串行外设接口模块的特点，并通过与MCS5l单片机通信，实现液晶显示。     

X-ray structure analysis and elastic properties of a fabric reinforced carbon/carbon composite

The effect of heat treatment on microstructure of a plain-weave carbon fabric reinforced carbon-carbon composite with phenolformaldehyde-derived carbon matrix was investigated by X-ray diffraction. The diffraction patterns were analysed by the least-square fitting program Carbonxs. After heat treatment from 1000 to 2800 °C the interplanar distance of (002) planes decreased from 3.488 to 3.420 Å and the lattice parameter in basal plane increased from 2.440 to 2.464 Å, respectively. Simultaneously, the coherent block size in the basal plane directions increased from 18 to 54 Å, which was accompanied by an increase of the fraction of organised carbon atoms from 0.50 to 0.85. The 002 diffraction profile of the composite was much narrower than the sum of peaks of the matrix and fabric alone. This can probably be caused by a better crystallographic ordering (or by a partial graphitisation) of the matrix in the composite. On the other hand, the composite Young’s modulus slightly decreased with the treatment temperature increasing from 2200 to 2800 °C in spite of the established strong improvement of fibre crystallinity and, therefore, fibre modulus. The mechanisms diminishing the modulus of composite (e.g. partial matrix graphitisation at the fibre/matrix interface and decreasing fibre/matrix contact area) probably prevailed over the increasing contribution of the fibre modulus.     

Possible tactics to improve the growth of single-walled carbon nanotubes by chemical vapor deposition

The growth time, growth mode and the method of preparing the supported catalysts play an important role in the growth of single-walled nanotubes (SWNTs). Their effects on the chemical vapor deposition (CVD) growth of SWNTs with MgO-supported catalysts were investigated in this study. It is shown that the growth rate of SWNTs was large during the initial few minutes of growth, however the quality of the tubes was low owing to the formation of many defects. Long term growth may favor the formation of tubes with high quality and high yield, but the introduction of other forms of carbon (impurities) is also unavoidable. There was a balance between the increase in yield and quality and sacrifice of the purity during growth of SWNTs. MgO-supported catalysts prepared by the co-precipitation method were found to be more effective for the synthesis of SWNTs than those prepared by the widely used impregnation method. The size and dispersion state of the catalyst were found to be crucial in enhancing the growth of SWNTs. In addition, growth on the surface of SWNTs over nanosized catalyst films was shown to be more favorable for the synthesis of tube products with higher quality, yield and purity.     

Understanding chemical reactions between carbons and NaOH and KOH: An insight into the chemical activation mechanism

Direct mixing of an anthracite with hydroxides (KOH or NaOH) and heat treatment up to 730 °C has shown to be a very good activation procedure to obtain activated carbons with very high surface areas and high micropore volumes. The reactions involved during the heat treatment of these hydroxide/anthracite mixtures have been analysed to deep into the fundamental of the knowledge of this chemical activation process, that has not been studied before. For this purpose, the present paper analyses the drying process, the atmosphere during the carbonisation, the chemical state of the activating agents (NaOH, KOH and Na₂CO₃) and the chemical reactions occurring during the heat treatment which have been followed by FTIR and TPD. The analysis of our results allows us to conclude that steam is a good atmosphere for the carbonisation process, alone or joined with nitrogen, but not as good as pure nitrogen. On the other hand, during the activation process, the presence of CO₂ should be avoided because it does not develop porosity. The reactions, and chemical changes, involved during this chemical process are discussed both from a thermodynamical point of view as well as identifying the reaction products (H₂ by TPD and Na₂CO₃ by FTIR). As a result, this paper helps to cover the present lack of understanding of the fundamentals of the reactions of an anthracite with hydroxides which are necessary to understand the activation of the material.     

Phase composition and properties of solid solutions of GdFeO3–GdInO3 bulks

Solid solutions of the GdFeO₃–GdInO₃ system were prepared at 1550 °C by ceramic powder processing. The formulated composition was Gd(Fe_1−xIn_x)O₃ (GFI) with the indium contents at x = 0, 0.25, 0.5, 0.75, and 1.0. A stable phase of Gd(Fe_1/3In_2/3)O₃ in our system was identified by X-ray diffraction and phase composition analysis. Multi-phase morphologies were observed for GFI bulks with x = 0.5 and 0.75. Dielectric and electrical properties of the GFI bulks were investigated. The addition of 25% In³⁺ in GdFeO₃ had an obvious enhancement in polarization and led to an elevated resonance frequency. Dielectric properties of GFI bulks except GdInO₃ were strongly dependent upon the test frequency, which corresponded to the response of polarization mechanism. GdInO₃ displayed as a stable dielectric, which was frequency- and temperature-insensitive. GdInO₃ was thermally activated and became leaky until above 600 °C.     

Material removal and surface damage in EDM of Ti3SiC2 ceramic

Material removal and surface damage of Ti₃SiC₂ ceramic during electrical discharge machining (EDM) were investigated. Melting and decomposition were found to be the main material removal mechanisms during the machining process. Material removal rate was enhanced acceleratively with increasing discharge current, i_e, working voltage, u_i, but increased deceleratively with pulse duration, t_e. Microcracks in the surface and loose grains in the subsurface resulted from thermal shock were confirmed, and the surface damage in Ti₃SiC₂ ceramic led to a degradation of both strength and reliability.     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。     

A complete VARMA modelling methodology based on scalar components

Abstract. This article proposes an extension to scalar component methodology for the identification and estimation of VARMA models. The complete methodology determines the exact positions of all free parameters in any VARMA model with a predetermined embedded scalar component structure. This leads to an exactly identified system of equations that is estimated using full information maximum likelihood.