Seismic behavior of geosynthetic-reinforced retaining walls backfilled with cohesive soil

This study investigates the seismic performance of geosynthetic-reinforced modular block retaining walls backfilled with cohesive, fine grained clay-sand soil mixture. Shaking table tests were performed for three ½ scaled (wall height 190 cm) and ¼ scaled model walls to investigate the effects of backfill type, the influence of reinforcement length and reinforcement stiffness effects. The El Centro and Kobe earthquake records of varying amplitudes were used as base acceleration. Displacement of the front wall, accelerations at different locations, strains on the reinforcements, and the visual observations of the facing and the backfill surface were used to evaluate the seismic performance of model walls. The model walls were subjected to rigorous shaking and the walls did not exhibit any stability problems or signs of impending failure. The maximum deformations observed on the models with cohesive backfill was less than half of the deformation of the sand model. The load transfers between the geogrid and cohesive soil was comparable to that of sand and hence the needed reinforcement length was similar as well. As a result; the model walls with cohesive backfills performed within acceptable limits under seismic loading conditions when compared with granular backfilled counterparts.     

坚持科技创新 打造强势企业

介绍了株洲硬质合金集团有限公司推进科技创新的具体做法,取得的主要成绩,以及今后的努力方向。     

WC15Ni磁合金的质量控制

在WC15Ni无磁硬质合金生产过程中,选用粒度分布范围较窄的优质WC以及添加适量的Cr3C2,促进了抗弯强度的提高。     

稀土元素对硬质合金高温性能的影响

采用动态热模拟试验技术，研究了添加微量稀土元素对硬质含金高温性能的影响。试验结果表明：添加微量稀土元素，能改善硬质合金高温性能，增加合金的塑性和高温韧性，降低硬质合金的热强性。     

低成本钢尾渣-矿渣基矿山充填料的优化开发

 为实现多固废协同利用、降低充填成本,在矿渣基全粒级细尾砂胶结充填料基础上,以流动性和抗压强度为表征,利用热闷钢渣磁选尾渣(钢尾渣)替代部分矿渣作为胶凝材料,脱硫灰和水泥熟料替代部分专用添加剂作为外加剂,采用正交试验探寻掺量规律,优化固体填充料配比,开发钢尾渣-矿渣基软性矿山充填料,并研究了外加剂与胶材比、灰砂比等因素的影响。对比分析了矿渣基准组、钢尾渣-矿渣基准组(B1)、强度最优外加剂组分钢尾渣-矿渣组(B7)等3组充填料的微观形貌及XRD图谱以探究其水化机理。结果表明,钢尾渣替代矿渣量增加、外加剂与胶材比减小,充填料浆流动性改善,但充填体抗压强度下降。强度正交试验结果表明,钢尾渣掺量大小决定强度低高,脱硫灰掺量宜高于水泥熟料。进一步调整外加剂组分配比,在灰砂比为1∶6、钢尾渣替代矿渣为20%条件下,找出B7组外加剂组分为脱硫灰、水泥熟料分别替代30%、20%专用添加剂,B7组料浆扩展度为143 mm,充填体形貌为富铁绿泥石胶结假方体钙硅灰石,28 d抗压强度达2.13 MPa,较基准组低0.19 MPa,较B1提高0.26 MPa。该替代方案满足现场充填C2级强度的要求,改善流动性并显著降低了充填成本。优化的外加剂组分配比在灰砂比为1∶4条件下同样具有强度优化作用,但较灰砂比为1∶6条件下低。     

Microstructures and properties of coating from cemented carbide by vacuum powder sintering

In this paper, the microstructures and properties of coating from cemented carbide of WC–Fe–Co–Ni on the substrate 45 steel are studied. The effects of sintering temperature on the microstructures of coating, the interface structures between coating and the substrate, the microhardness distribution and its wear resistance in the coating are investigated. The results indicate that the coating is strongly metallurgical bonded with the substrate by the mutual diffusion and penetration of Fe towards the coating and W, Co, Ni towards the substrate at sintering temperature ranging from 1280 °C to 1300 °C. The coating obtained exhibits compact structure and uniformly distribution of WC with fine grain and porosity free from defects, having high microhardness and preferable wear resistance.     

Cemented backfill technology based on phosphorous gypsum

Physical-chemical properties of phosphorous gypsum, proportion and cemented mechanism of slurry with gypsum as aggregate were studied to remove the harms of gypsum pile, combining with difficult problems of excessive mined-out gobs, enormous ore body under roadway and low recovery ratio of Yongshaba Mine, Kaiyang Phosphor Mine Group, Guizhou Province, China. An appropriate backfill system and craftwork were designed, using shattering milling method to crush gypsum, double-axles mixing and strong activation mixing way to mix slurry, cemented slurry and mullock backfill alternately process. The results show that gypsum is fit for backfilling afterwards by adding fly ash, though it is not an ideal aggregate for fine granule and coagulate retardation. The suggested dosage (the mass ratio of cement to fly ash to gypsum) is 1:1:6–1:1:8 with mass fraction of solid materials 60%–63%. Slurry is transported in suspend state with non-plastic strength, and then in concretion state after backfilling. The application to mine shows the technology is feasible, and gypsum utilization ratio is up to 100%. Transportation and backfill effect is very good for paste-like slurry and drenching cemented slurry into mullock, and the compressive strength and recovery ratio are 2.0 MPa and 82.6%, respectively, with the maximum subsidence of surface only 1.307 mm. Furthermore, the investment of system is about 7×10⁶ yuan (RMB), only 1/10 of that of traditional paste backfill system. Foundation item: Project (2006BAB02A03) supported by the National Key Technology Research and Development Program; Project (08MX16) supported by Mittal Scientific and Technological Innovation Projects of Central South University during 2008     

多目标条件下矿山充填材料配比优化实验

为准确确定某铁矿尾砂胶结充填材料最优配比,分别选择制浆水性、砂灰质量比和料浆质量浓度与充填体强度、料浆坍落度和料浆泌水率作为尾砂胶结充填材料配比优化的影响因素和充填性能评价指标.基于响应面–满意度函数耦合理论,采用Box-Behnken实验设计方法开展13组不同充填配比实验,构建充填性能评价指标的响应面函数,研究各影响因素与目标响应量的相关关系及多目标条件下的最优充填材料配比.结果表明,制浆水性对响应量影响不显著;砂灰质量比对充填体强度影响极显著;坍落度受料浆质量浓度、砂灰质量比影响较显著;砂灰质量比和料浆质量浓度对料浆泌水率的影响均极为显著,且二者之间存在极显著的交互作用.该矿尾砂胶结充填材料最优配比为:制浆水性为海水,砂灰质量比为8.44:1,料浆质量浓度为72%,该配比条件下对应的响应量预测结果为:充填体28 d龄期单轴抗压强度为2.00 MPa,料浆塌落度为27.15 cm,料浆泌水率为7.35%,与验证实验结果基本吻合,为现场工业实验提供强有力的理论支撑.     

软土地区旧桩拔除技术和新建桩基础调整方案及施工措施

结合天津南开区某地块定向经济适用房项目,介绍其在基础施工中遇到旧预制方桩时,采用全套管高压喷气、射水振动沉管施工工艺清孔拔桩,并对该工艺进行分析得出:该拔桩施工工艺适用于软土地区旧桩拔除项目;并针对旧桩孔无法回填压实、部分新建桩基础与拔除旧桩孔距离较近等原因导致钻孔倾斜、串孔等问题,提出远离旧桩位置或调整至旧桩桩心位置等方法调整桩位,并采用加大桩径、增设承台等调整方案承担因调整桩位而产生的上部偏心荷载;采用拌和白灰、分层压实、回填静置等措施提高回填土的密实度,采用保证垂直度和调节泥浆配合比等措施,以改善不良施工条件,得出适当增加混凝土充盈系数保证成桩质量等施工经验,为后续类似工程提供借鉴。