高放废液化学成分分析

概述了高放废液中25种阳离子、5种阴离子以及总蒸残物、总氧化物、密度和游离酸的分析方法。对核燃料后处理高放废液进行取样分析,其主要化学成分采用两种以上不同原理的方法作对比测定,结果相互符合情况良好,为高放废液处理处置研究设计,提供了完整、准确的基础数据。     

Surface characteristics of fluorine-modified PAN-based carbon fibers

Different fluorination methods were applied to modify the surface properties of carbon fibers. The relationship between the degree of fluorination and the physicochemical properties of carbon fibers was studied using a combination of mechanical tests, elemental analysis (EA), X-ray photoelectron spectrometry (XPS), and X-ray diffraction (XRD). EA and XPS analyses of fluorinated carbon fibers showed that treatment with mixtures of F₂/O₂ introduced a much higher fluorine concentration than that with F₂ only. However, XRD analysis showed that there was no increase in the interlayer distance, due to the mild fluorination condition applied. Consequently, the oxyfluorination was one of the more effective methods to increase surface polarity of carbon fibers, which probably played an important role in improving the tensile properties of the fibers in the epoxy resin system.     

Decomposition of Time Series Dynamic Linear Models

This paper derives the admissible decompositions for a time series dynamic linear model, assuming only that the model is observable. The decompositions depend on factorizations of the characteristic polynomial of the state evolution matrix G into relatively prime factors. This generalizes the method of West (1997 ) which considers one decomposition in the particular case where G is diagonalizable. Conditions are derived for a decomposition to be independent. These results show that no autoregressive process of order d has an independent decomposition for any integer d . Two illustrations of this procedure are discussed in detail.     

略论贵州省化工企业职业教育的发展

从目前市场需求和就业率出发，进行形势分析，提出优化专业设置、加强实践环节、提高高职学院办学层次、推进“双证书”制度等改革方法，以促进化工职业教育的发展。     

Analytical characterization of cadmium cyanamide in CdS thin films and bulk precipitates produced from CBD process in pilot plant

CdS thin films and bulk precipitates were obtained by chemical bath deposition (CBD) in a well-closed reactor. X-ray diffraction spectroscopy, Fourier transform infrared spectroscopy, thermal analysis, elemental analysis and leaching have been used to characterize solids and thin films. It has been shown that the proportion of cadmium cyanamide in solids may vary from about 50% to 2% according to physicochemical conditions in solution (time after CBD, ammonia concentration) and that CdO results from CdCN₂ after air annealing of thin films. This last step also increases the crystallinity of the films.     

Heavy arsenic doping of silicon grown by atmospheric pressure selective epitaxial chemical vapor deposition

Selective epitaxial Si with a high arsenic concentration of 2.2×10¹⁹ atoms/cm³ was deposited at a high growth rate of 3.3 nm/min under atmospheric pressure. It was confirmed that this method had excellent selectivity and produced films having good crystalline quality, abrupt dopant profiles at the interfaces, and smooth surfaces. The growth mechanism is discussed in terms of the relationship between the effects of arsenic surface segregation and etching by hydrogen chloride.     

Quantitative measurement of gas hold-up distribution in a stirred chemical reactor using X-ray cone-beam computed tomography

Cone-beam type X-ray computed tomography (CBCT) is a potential method to measure three-dimensional phase distributions in vessels. An example for that is the measurement of gas profiles in stirred chemical reactors. Such data are highly valuable for the assessment and evaluation of chemical processes, for optimisation of the reactor and stirrer design, and for evaluation of computational fluid dynamics codes used to model the fluid flow and heat transfer in reactive systems. However, there are considerable difficulties for accurate quantitative measurements due to beam hardening and radiation scattering effects. In a theoretical and experimental work we have investigated the non-linear effects of both physical phenomena and developed a suitable measurement setup as well as calibration and software correction methods to achieve a highly accurate measurement of void fraction profiles with CBCT.     

A complete VARMA modelling methodology based on scalar components

Abstract. This article proposes an extension to scalar component methodology for the identification and estimation of VARMA models. The complete methodology determines the exact positions of all free parameters in any VARMA model with a predetermined embedded scalar component structure. This leads to an exactly identified system of equations that is estimated using full information maximum likelihood.     

GC–MS characterization of oligomers in polyadipates used as plasticizers for PVC in food contact

Fourteen commercial polyadipates and a polysebacate were analysed for their components of a molecular mass below 1000 Da, primarily with the aim of generating the background data for measuring the migration of this type of polymeric additives from plasticized PVC (e.g. cling films and gaskets of lids) into foods or food simulants. Since the composition of the material <1000 Da varies between the polyadipates, the main components must be identified to enable a correct quantification. Polyadipates differ in the diol used as linker, their termination (acid or alcohol) and in the end‐capping (free alcohols, acetylation, acylation with fatty acids, esterification with octanol/decanol). Gas chromatography (GC) provides good separation, but the material remaining in the column up to high temperatures decomposes and forms a hump in the rear part of the chromatogram. Examples of mass spectra are shown, the most indicative fragments pointed out and spectra of 159 components listed. The polyadipates and the sebacate are characterized by their structure, the main components <1000 Da and the fraction of material <1000 Da. Copyright © 2006 John Wiley & Sons, Ltd.