Determination of heavy metals and volatile aromatic compounds in used engine oils and sludges

Assessment of contaminant releases during utilization of used oils is essential for the determination of environmental acceptability. These paper reports the results of the study examining a toxic metal leachability from used engine oil and sludge samples employing leaching test (TCLP). The leaching test indicated that lead in oil samples exceeded 5-ppm concentration level what qualified them as a toxic waste. The samples of contaminated sludge were found to contain high concentration of total lead, barium and chromium, but the leaching test showed concentration below regulatory limit. The total content of benzene, ethylbenzene, toluene, and xylenes (BETX), and naphthalene in used oil and sludge samples was also determined and was found not to be a significant factor to contamination.     

The Structure of the Irreversibly Bound Adhesion Promoter-Substrate Interfacial Layer of γ-Aminopropylsilanetriol on Crystalline Si, as Measured by XPS and FTIR

The irreversibly bound interfacial layer deposited by the γ-aminopropysilanetriol adhesion promoter onto a crystalline silicon substrate, which remains even after profuse washing, was found by XPS to have resulted from the fragmentation and rearrangement of the original γ-aminopropylsilanetriol molecule. A mechanism is proposed, involving the homolytic scission of the terminal N-C bond. One of the subsequent reactions is believed to involve hydrogen loss by abstraction and the formation of a terminal vinyl group, which bonds to the substrate. Support for this mechanism is found in IR spectroscopy of this layer.     

湿法磷酸过滤设备和管道结垢原因分析及控制研究

分析湿法磷酸过滤设备与管道结垢的主要原因是氟硅酸钾、钠盐因磷酸液相温度下降而沉积下来。提出采用添加剂,抑制或提前析出氟硅酸钾、钠盐,同时进行了5种添加剂的实验室研究:均有较好的阻垢效果,但最终选择添加剂E(氟硅酸),阻垢率可达70%以上,添加量以0.5g/100g磷矿为宜。     

Growth of sculptured polymer submicronwire assemblies by vapor deposition

We have grown helical nanowire assemblies of parylene C, thereby demonstrating that polymeric sculptured thin films (STFs) can be fabricated by a combination of physical and chemical vapor deposition processes. The deposition method is explained in detail and electron micrographs of 200-400 nm size sculptured thin film of parylene are given. The shapes of the submicron and nanowire assemblies can be engineered so that the polymeric STF acts as a template for preferential attachment of biomolecules.     

Zinc Coated Steel/Epoxy Adhesive Systems: Investigation of the Interfacial Zone by FTIR Spectroscopy

The present study takes advantage of the ability of Fourier Transform Infrared Spectroscopy (FTIR) for the analysis of ultrathin organic films on metals. FTIR in the reflection mode (IRRAS) is used in order to study the interaction of ultrathin films of dicyandiamide (hardener of most one-pack epoxy resins) with various substrates, model ones such as gold or zinc and industrial ones such as steel and zinc-coated steels.

Pure zinc surfaces and, to a lesser extent, zinc-coated steels are shown to react with dicyandiamide after heating at 180°C, as evidenced by the frequency shift of the absorption band (at about 2200 cm^-1) characteristic for nitrile groups. As real systems consist of thick layers of a fully formulated adhesive cured onto a metallic substrate, the direct investigation of such a buried interphase is no longer possible by FTIR and by most of the known spectroscopies. Some mechanically tested specimens are then analysed, after failure, by FTIR microspectrometry. The spectra obtained, corresponding to the fracture initiation zone which is about 100 μm in diameter, advocate for the presence of an ultrathin layer of modified polymer still covering the substrate.     

有限元方法在离心机转鼓强度分析中的应用

在回顾以往转鼓强度分析的基础上 ,指出了目前转鼓有限元应力分析所存在的问题 ,给出了提高计算精度和保证模拟有效性的注意事项 ,并探讨了转鼓强度评定准则     

用预分解技术改造Φ4×60m预热器窑的又一成功实例

介绍南京水泥工业设计研究院用预分解生产技术对山东水泥厂Φ4×60m预热器窑烧成系统进行的成功技术改造。技改设计指标为：熟料产量保证指标1500t／d，争取指标1700t／d，熟料热耗＜3762kJ／kg，熟料28d抗压强度＞60MPa。整个工程停产施工耗时仅用48d，烧成系统技改共耗资约3000万元。技改后一次点火投料成功，且点火当月即实现72h达标考核，所有设计指标均达标。     

Dynamics of fluid circulation in coupled free and heterogeneous porous domains

Fluid flow in coupled free and porous domain, particularly when the porous medium is heterogeneous, is encountered in many hydro-environmental conditions, e.g., leakage from underground pipe, combined groundwater lake-subsurface interactions. One of the most difficult problems in the study of coupled flow behaviour has been the development of a universally applicable modelling scheme for combining the flow regimes. This is because the free/porous interfacial properties (e.g., shear-stress; velocity slip) that govern the coupled flow behaviour are difficult to determine experimentally under hydro-environmental conditions. On the other hand, the implications of various forms of heterogeneity in the porous media properties can be very different on the fluid-flow behaviour. Difficulties may also arise in direct coupling of the model equations that govern the fluid flow in the individual regions (e.g., Navier-Stokes for free-flow region and the Darcy's equation for the porous flow region). Consequently, models of coupled free and porous flow for hydro-environmental conditions are not very well developed at the moment. While there are some indications that fluids in coupled free and porous domains may circulate (i.e., development of flow cells), there is a lack of appropriate 3D analysis on how heterogeneities in porous media may affect such flow patterns. In this paper, we aim to analyse how porous media heterogeneity affects the dynamics of flow circulation in the porous side of a coupled free and porous domain. For this purpose, we analyse flow patterns in several model domains made up of two porous layers with differing permeabilities. The governing model equations are discretised and solved using the standard finite volume method on a staggered cell-centred mesh. The temporal discretisation is done using the explicit method. An in-house graphical user interface (GUI) has been created specifically to aid in the visualisation of otherwise complex flow patterns. The GUI contains many post-processing options and provides a comprehensive tool for the analysis of hydrodynamics and contaminant motion (not discussed in this paper) in coupled free and porous flow domains. This GUI is described in this paper briefly. The effects of altering the aspect ratio (i.e., multi-scale) of the domain on the coupled flow pattern have also been discussed.     

对甲醇精馏几个问题的认识

简述甲醇精馏三塔流程原理 ,分析了加压精馏塔及常压精馏塔物料和热量平衡关系 ,提出了操作中应注意的事项     

新型节能玻璃钢门窗的研究

本文主要围绕节能主题，从能耗方式、性能指标、结构形式、制作安装等方面论述了玻璃钢门窗在不同气候地区、不同环境和不同领域中的开发和应用。