弹性杆与水下壳体接触冲击的冲击力计算研究

对弹性杆与水下壳体接触冲击问题进行了研究，用有限元法模拟壳体，边界无法模拟无限域流体，通过温面上的耦合条件进行联立求解，文中给出了典型算例，并进行了有关讨论。     

滁州市农贸市场超长预应力楼盖的设计分析

滁州市农贸市场超长预应力楼盖温度应力有限元分析及设计原则。     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

石油钻机提升系统穿绳方法研究

目前国内外钻机大绳一般采用顺穿法或花穿法。分析了2种穿绳方法的受力特点,大绳顺穿时游车的受力不平衡,会发生倾斜和摆动;采用大绳花穿方法,避免了游车的倾斜和摆动,但造成大绳入轮槽的倾角大,大绳易脱槽。顺穿法一般在电动钻机上采用,主要考虑到电控操作提升系统比较平稳;花穿法一般在机械钻机上使用,以受力平衡来缓解气控操作带来的冲击载荷的影响。为了克服这2种穿绳方法的不足,提出了两行双联滑轮组顺穿法和双联滑轮组顺穿法,可以提高安全性,减少磨损。     

高压注水管柱受力分析

进行高压注水管柱受力分析的目的就是根据注水条件研究注水管柱在不同过程中的各类效应，以及这些效应对管柱产生的受力和变形规律，从而明确注水管柱的工作状态，保障注水管柱有效合理地工作。较详细地分析了高压注水管柱在锚定、坐封以及注水3个过程中的受力状态和变形情况，并分析了高压注水管柱在不同过程中受到的各种效应的影响，推导出注水管柱在不同过程中的应力及变形的计算公式，并给出了算例。     

高层建筑结构设计特点与剪力墙设计

围绕高层建筑结构，总结了高层建筑结构设计的特点，提出了剪力墙设计的几个问题，以及高层建筑结构分析和各种体系相对应的方法。     

谐振式力传感器敏感结构的研究

利用材料力学及弹性力学法，对石英晶体谐振式力传感器的悬臂梁结构进行了研究，得出了双梁单岛及三梁单岛悬臂梁结构的力转移系数，在与实验结果进行了比较后证明，支承结构的理论推导与实验结果一致。     

Three-parameter vs. two-parameter Weibull distribution for pultruded composite material properties

The three-parameter and two-parameter Weibull distributions are compared using 26 mechanical property data sets of fiber-reinforced polymeric (FRP) composite materials manufactured by the pultrusion process. Both strength and stiffness properties were examined. The probability distributions were compared on the basis of goodness of fit, nominal design values, and allowable load to achieve uniform reliability. It is recommended that the two-parameter Weibull distribution be used to characterize FRP composite material properties. The primary basis for this recommendation is small differences in nominal design values and small differences in allowable loads between the two-parameter and three-parameter Weibull distributions. Other supporting reasons for the recommendation are similar observed significance levels in distribution fitting, computational efficiency, and the fact that the location parameter of the three-parameter Weibull distribution is near the first order statistic.     

单桩腿有限元分析

为保证桩腿在冬季冰区海域的安全使用,对桩腿结构进行冰载荷作用下的强度分析。应用ANSYS软件建立桩腿、地基、冰相互作用的仿真计算模型,实现桩腿的力学分析。对桩腿进行了强度校核,计算出冰载荷作用下桩腿的变形及其应力状态。计算结果表明,桩腿在此冰载荷作用下强度满足安全要求。