Effect of hot pressing on processing and properties of BBN ceramics

BBN (BaBi₂Nb₂O₉) is very interesting and promising lead free material with relaxor properties in capacitors, sensors and actuators.     

Novel electro-optic properties of epitaxially grown (Pb, La)(Zr, Ti)O3 (PLZT) thin films derived by advanced sol–gel methods

Advanced sol–gel methods using a secondary solvent addition into (Pb, La)(Zr, Ti)O₃ (PLZT) sol–gel solution and a methanol pre-treatment of sapphire substrates are demonstrated. For the secondary solvent addition, the additive affected the crystallinity and electro-optic (EO) property of PLZT films and only methanol addition can improve them. In addition, the methanol pre-treatment is also appeared to be effective to improve film characteristics.

Through these optimizations, epitaxially grown PLZT thin films on r-cut sapphire are obtained and a high Pockels coefficient which is comparable to those of bulk PLZTs is achieved. It is believed that these PLZT thin films are applicable for integrated EO devices and open the door for the future data communication systems.     

C语言学习方法与实践的探讨

针对C语言程序设计课程本身的特点，分析学习过程中存在的问题，强调实践的必要性。结合一些学校课程改革和实践的经验．提出面向应用的，科学的学习内容、方法和模式。同时提高学习者的专业动手能力。     

On-line corrosion monitoring in geothermal district heating systems. II. Localized corrosion

Corrosion monitoring in district heating systems has traditionally been performed by using off-line methods, such as weight loss. The disadvantage is that the method is very slow, especially in low-corrosive environments, and that it only provides information about the past corrosion (accumulated over period of time). The purpose of the work is to test on-line monitoring methods in geothermal hot water in the district heating system in Reykjavik, Iceland. Geothermal water poses certain problems with regards to corrosion monitoring due to low conductivity, high pH and the presence of sulphide. These conditions make the geothermal environment low corrosive. However, a quality control is needed, especially since the sulphide causes the steel pipes to be more vulnerable towards localized corrosion. The methods used in this study were: linear polarization resistance (LPR), harmonic analysis (HA), electrochemical noise (EN) and zero resistance ammetry (ZRA). The Pitting Factor was measured with EN and showed promising results for measuring-localized corrosion on-line. A crevice corrosion cell also gave good results but had a low lifetime. However, the results of a galvanic corrosion cell (Fe/Cu) proved more difficult to interpret since they were dependent both on the dissolved oxygen and the sulphide level.     

Preparation of one-dimensional polymer films by modification of a hydroxymethylbenzene self-assembled monolayer on iron with alkyltriethoxysilanes for preventing iron corrosion

A self-assembled monolayer (SAM) of p-hydroxymethylbenzene HOCH₂C₆H₄ - (HOMB) moiety adsorbed on iron by the formation of a covalent bond between carbon and iron atoms was prepared by electrochemical derivatization of an iron electrode with p-hydroxymethylbenzenediazonium tetrafluoroborate HOCH₂C₆H₄N₂BF₄. The electrode covered with the HOMB SAM was modified with alkyltriethoxysilanes C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 or 18) to prepare a film of one-dimensional polymer. The protective ability of the polymer film was determined by polarization measurement of the covered electrode in an aerated 0.5 M NaCl solution. The ability was enhanced by modification of the HOMB SAM with C_nTES markedly. The iron surface coated with the one-dimensional polymer film of the HOMB SAM modified with C₈TES was characterized by contact angle measurement and FTIR reflection and X-ray photoelectron spectroscopies. The persistence in the protective ability of the polymer film against iron corrosion in 0.5 M NaCl may be associated with the strong adsorption via the covalent bond, revealed by electron-probe microanalysis.     

Finite sample properties of estimators of spatial autoregressive models with autoregressive disturbances

The article investigates the finite sample properties of estimators for spatial autoregressive models where the disturbance terms may follow a spatial autoregressive process. In particular we investigate the finite sample behavior of the feasible generalized spatial two-stage least squares (FGS2SLS) estimator introduced by Kelejian and Prucha (1998), the maximum likelihood (ML) estimator, as well as that of several other estimators. We find that the FGS2SLS estimator is virtually as efficient as the ML estimator. This is important because the ML estimator is computationally burdensome, and may even be forbidding in large samples, while the FGS2SLS estimator remains computationally feasible in large samples. Received: 20 January 2001 / Accepted: 31 August 2001     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

GLU♮ embedded in C++: a marriage between multidimensional and object‐oriented programming

The embedding of a small but expressive language of multidimensional functional programming in a well known and widely used language of object‐oriented programming leads to the combination of two radically different programming models. In this paper, we formally define the syntax and semantics of GLU^?, which can be thought of as the multidimensional core of Lucid and GLU, and we describe its implementation as a language embedded in C++. With the aid of a few examples, we argue that the marriage of the two programming models is not only compatible and natural, but also that it produces a new and interesting hybrid language. Copyright © 2004 John Wiley & Sons, Ltd.