杀菌剂苯菌灵的结构鉴定及其核磁共振研究

用红外、质谱、核磁共振等手段确证了江阴农药厂合成的苯菌灵的化学结构,并进行了该化合物核磁共振谱线的归属。     

广西某矿区托帕石的宝石学特征

广西某矿区的脉石矿物——黄玉分三个世代,其中第三世代的黄玉晶体无色透明,重量大于0.9克拉,瑕疵不明显,密度(3.50)、硬度(7.8430)和折射率(1.6330)等特征均达宝石级,经系统研究测试,可以命名为托帕石(Topaz)。     

STM tunneling spectroscopy on high Tc superconductors

STM tunneling spectroscopy has been performed on the bulk single crystals of BiSrCaCuO (BSCCO) and the epitaxial thin films of YBaCuO (YBCO) at cryogenic temperatures. The STM images and tunneling spectra observed on the (001) surfaces can be classified into three cases; 1) Atomic image is visible. However, the tunneling spectrum shows semiconducting or smeared superconducting gap structures, depending on the tip-sample distance. 2) Clear atomic image can not be obtained. But, the tunneling spectrum shows flat bottom region with quite low zero bias conductance. 3) Tunneling spectra demonstrate gapless behavior, independent of the tip-sample separation. These observations support the quasi-2D electronic picture in whichs-wave like 2D superconducting layers are coupled with each other through the Josephson effect.     

Structural reliability optimization using an efficient safety index calculation procedure

The objective of this paper is to conduct reliability-based structural optimization in a multidisciplinary environment. An efficient reliability analysis is developed by expanding the limit functions in terms of intermediate design variables. The design constraints are approximated using multivariate splines in searching for the optimum. The reduction in computational cost realized in safety index calculation and optimization are demonstrated through several structural problems. This paper presents safety index computation, analytical sensitivity analysis of reliability constraints and optimization using truss, frame and plate examples.     

测井相识别模型及其在东海油气勘探中的应用

文章提出一种测井相识别模型,该模型用常规测井信息,定量地确定测井相在钻遇地层中的空间位置,建立测井相。配合东海油气勘探工作,用该识别模型对苏堤构造带的钻遇地层进行了测井相分析。     

贵冶动力中心二期反渗透系统改造

本文阐述对贵冶动力车间二期反渗透进行改造的成功实践 ,主要从反渗透系统设计、反渗透系统中容易出现的问题及解决方法等进行介绍。     

Optimum thermoeconomic and thermodynamic performance characteristics of an irreversible three-heat-source heat pump

The coefficient of performance and specific heating load of an irreversible three-heat-source heat pump are given by using a general cycle model affected by the finite-rate heat transfer, heat leak and internal irreversibility of the cyclic working fluid. The heat pumping load divided by the total cost per unit time is taken as a new objective function and used to investigate the performance of the heat pump. The thermoeconomic and thermodynamic performance characteristics of the heat pump are discussed in detail. Some important performance parameters such as the thermoeconomic objective function and coefficient of performance are optimized. The optimally operating regions of the heat pump and the bounds of several performance parameters are determined. Finally, it is pointed out that the Carnot heat pump may be taken as a special case of a three-heat-source heat pump and consequently its optimal performance can be directly derived from the results obtained here.     

浅议斜坡稳定性计算中水压力的作用

理论推导证明了静水压力模式与动水压力模式下地下水作用效果的差异,并且结合前人的研究成果,提出要取得合理的稳定性计算结果,两种水压力模式下所选用的强度参数应有所区分,对于静水压力模式,应取快剪或不排水剪指标;对于动水压力模式,则应取用慢剪或排水剪指标。最后采用一个具体的工程实例验证了结论的合理性。     

高层建筑结构设计的分析判断与优化

对高层建筑设计而言,设计前期的初步结构方案需通过结构软件的计算分析,判断该方案是否正确与合理,从而对其进行有针对性的修改和优化。文章结合具体实例,介绍了分析判断计算结果的主要几项内容及可采取的相应优化措施,从而可以提高设计的准确性和工作效率。     

论工艺参数对烧结产质量的影响及分析

本文论述了正确认识烧结工艺参数对搞好烧结生产的意义，介绍了烧结工艺参数其及相互关系，详述了烧结主要工艺参数对其产质量的影响，提出了烧结工艺参数认识的几点结论性意见。