Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

Alloy optimisation of bainitic steel for large plastic mould

Based on the phase transformation theories, especially the T₀ concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C?s^??1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050?mm.     

Design structure matrix (DSM) method application to issue of modeling and analyzing the fault tree of a wind energy asset

The perpetual energy production of a wind farm could be accomplished (under proper weather conditions) if no failures occurred. But even the best possible design, manufacturing, and maintenance of a system cannot eliminate the failure possibility. In order to understand and minimize the system failures, the most crucial components of the wind turbines, which are prone to failures, should be identified. Moreover, it is essential to determine and classify the criticality of the system failures according to the impact of these failure events on wind turbine safety. The present study is processing the failure data from a wind farm and uses the Fault Tree Analysis as a baseline for applying the Design Structure Matrix technique to reveal the failure and risk interactions between wind turbine subsystems. Based on the analysis performed and by introducing new importance measures, the “readiness to fail” of a subsystem in conjunction with the “failure riskiness” can determine the “failure criticality.” The value of the failure criticality can define the frame within which interventions could be done. The arising interventions could be applied either to the whole system or could be focused in specified pairs of wind turbine subsystems. In conclusion, the method analyzed in the present research can be effectively applied by the wind turbine manufacturers and the wind farm operators as an operation framework, which can lead to a limited (as possible) design‐out maintenance cost, failures' minimization, and safety maximization for the whole wind turbine system.     

大直径平底负压容器优化设计

通过对大直径平底负压容器平底板的设计计算,平底板计算厚度很厚。通过分析,提出了对平底板采取加强措施,从而减薄平底板计算厚度的方法。该容器在实际生产过程中性能可靠、稳定,对类似设备设计具有借鉴意义。     

Predicting visual similarity between colour palettes

This work is concerned with the prediction of visual colour difference between pairs of palettes. In this study, the palettes contained five colours arranged in a horizontal row. A total of 95 pairs of palettes were rated for visual difference by 20 participants. The colour difference between the palettes was predicted using two algorithms, each based on one of six colour-difference formulae. The best performance (r² = 0.86 and STRESS = 16.9) was obtained using the minimum colour-difference algorithm (MICDM) using the CIEDE2000 equation with a lightness weighing of 2. There was some evidence that the order (or arrangement) of the colours in the palettes was a factor affecting the visual colour differences although the MICDM algorithm does not take order into account. Application of this algorithm is intended for digital design workflows where colour palettes are generated automatically using machine learning and for comparing palettes obtained from psychophysical studies to explore, for example, the effect of culture, age, or gender on colour associations.     

Kinetic,thermodynamic parameters and in vitro digestion of tannase from Aspergillus tamarii URM 7115

Tannase is an enzyme used in various industries and produced by a large number of microorganisms. The aim of this study was to evaluate tannase production to determine the biochemical, kinetic, and thermodynamic properties and to simulate tannase in vitro digestion. The tannase-producing fungal strain was isolated from “jamun” leaves and identified as Aspergillus tamarii. Temperature at 26°C for 67?h was the best combination for maximum tannase activity (6.35-fold; initial activity in Plackett–Burman design—15.53?U/mL and average final activity in Doehlert design—98.68?U/mL). The crude extract of tannase was optimally active at 40°C, pH 5.5 and 6.5. Moreover, tannase was stimulated by Na⁺, Ca²⁺, Mg²⁺, and Mn²⁺. The half-life at 40°C lasted 247.55?min. The free energy of Gibbs, enthalpy, and entropy, at 40°C, was 81.47, 16.85, and ?0.21?kJ/mol?·?K, respectively. After total digestion, 123.95% of the original activity was retained. Results suggested that tannase from A. tamarii URM 7115 is an enzyme of interest for industrial applications, such as gallic acid production, additive for feed industry, and for beverage manufacturing, due to its catalytic and thermodynamic properties.     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

张峰水库溢洪道体型优化设计

本文对已设计的张峰水库溢洪道进行了模型试验,根据对试验结果分析,认为原方案设计存在一些问题,并针对问题进行了优化设计。通过对修改方案模型试验结果分析,得出修改方案改进了原方案中存在的不足,优化合理,是可以采用的。