精密角位移传感器及其可靠性研究

从理论上探讨了磁阻率效应，叙述了精密角位移传感器的工作原理及结构设计。传感器的分辨率已达０．０１°，通过可靠性寿命试验，传感器的失效率λ（ｔ）＜１×１０－７／ｈ。     

Dynamics of Solidification in 2% Corn Starch-Water Mixtures: Effect of Variations in Freezing Rate on Product Homogeneity

Directional solidification studies of gelatinized corn starch-water mixtures were undertaken in order to examine, in situ, the freezing behavior of this food model. The solidification rate was controlled by varying sample cell velocity as it moved from a 25°C hot stage to a -25°C cold stage. While freezing at cell velocities ≤7.5 μm/sec, starch granules were alternately pushed or entrapped by the advancing solid-liquid interface producing a segregated structure consisting of alternating high-starch and low-starch bands. At a cell velocity of 10 μm/sec, the frozen product was homogeneous. The relationship between the solid-liquid interface velocity and segregation behavior was quantified and compared to an existing model of particle-interface interactions.     

Additives distribution and electrical properties in zinc oxide varistor prepared by a wet chemical method

Cobalt-, praseodymium-added zinc oxide varistor was prepared through a wet chemical method followed by sintering with or without calcination. Changes in grain size, compact density, additives distribution, and voltagecurrent/ capacitance-voltage relations were investigated for the characterization of the samples sintered at temperatures from 1473 to 1573 K without calcination or with calcination at 773 K for 2 h. The electrical properties were compared with nhose of samples prepared by two types of ball mill methods. The wet chemical method provided almost the same additives-distribution profile and less impurities in comparison with the ball grinding method carried out for 10–100 h. The donor concentration and the potential-barrier height for the samples were evaluated by Double Schottky Barrier Model. Addition of small amount of both cobalt and praseodymium in preparation by the wet chemical method was effective for a better nonlinearity relation between voltage and current, which has potential for a smaller sized varistor.     

单小区模型的掉话率分析

掉话率是无线通信网络中最重要的关键性能指标(KPI)之一,本文分析了中国移动在讨论网络性能评估方法时提出的3个不同的掉话率计算公式,通过建立一个单小区的模型,使用一些合理的假设和分析,从理论上确定了一个最为准确的计算公式.     

膜片式流量调节阀

介绍了用于油田开采工艺的膜片式流量调节阀的结构及其特点,分析了调节阀出口压力、进口压力对其流量的影响。受力分析和现场使用表明:该阀流量恒定精度(即恒流偏差)取决于膜片有效面积S与阀心下端有效面积S′之比,此值为12,其恒流比偏差为0·03,说明该阀的流量恒定精度高;该阀不易被杂质卡死,稀油中直径1mm的砂粒能顺利通过,而不影响阀的功能;膜片式流量调节阀是没有高加工精度要求的部件,普通车床即可生产,因此造价较低。     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Quasi-static and dynamic crushing behaviors of aluminum and steel tubes with a cutout

Tubular members are commonly used as an energy absorber in engineering structures and many such members have a cutout. In this study, the crushing behaviors of tubes with a cutout are characterized and the effects of cutout on the energy absorption capabilities of these tubes are quantified. Systematic parametric studies were carried out to study the effect of material properties, including yield and ultimate strength of material, strain rate effect, location of cutout, tube length and impact speed on the crushing behaviors and energy absorption capacity of aluminum and steel tubes. First, a numerical model was constructed with a commercial explicit finite element code. It will be first proven that the numerical simulation can produce sufficiently accurate results in an economic manner. Subsequently, the crushing behavior of aluminum and steel tubes with a cutout was experimentally characterized and their energy absorption capacity was evaluated in terms of mean crushing force, peak crushing force and specific energy absorption (SEA). Tubes of various lengths with a cutout located at different locations, subject to both quasi-static and dynamic impact loadings were considered. For steel tubes, the numerical simulation investigated the influence of the strain rate effect and variation in strain hardening ratio of the material. Empirical equations describing the mean and peak crushing forces of aluminum and steel tubes with a cutout were developed using linear and nonlinear regression methods applied to the results obtained from the numerical and experimental studies.     

Turbo码中快速交织器的设计

分析了交织器在Ｔｕｒｂｏ码中的重要作用，以及目前交织器存在的缺陷，介绍了一种快速交织器的设计方法。该交织器易于实现，具有交织时延低的突出优点。计算机仿真结果表明，该快速交织器可以获得优异的性能。     

Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.