无机阻燃剂高聚合度聚磷酸铵的研制

以五氧化二磷、磷酸铵盐、尿素为原料、氨气为保护气,制备了高聚合度聚磷酸铵无机阻燃剂。考察了五氧化二磷、磷酸铵盐、尿素的用量和反应温度对聚磷酸铵平均聚合度的影响。采用端基滴定法测定了聚磷酸铵的聚合度,并用X射线衍射(XRD)法表征了聚磷酸铵的晶体结构,同时测定了聚磷酸铵的粒度和溶解度。实验结果表明,制备聚磷酸铵的最佳反应条件为:n(磷酸氢二铵)∶n(五氧化二磷)∶n(尿素)=1∶1∶0.3,反应温度280~300℃,反应时间40m in,热处理温度250~280℃,热处理时间110m in。在此条件下制备的聚磷酸铵的平均聚合度大于600,平均粒径直径小于50μm,在水中的溶解度小于0.4g;XRD表征结果表明,所合成的物质为Ⅱ型聚磷酸铵。     

云南磷肥工业副产氟资源综合利用途径初探

根据云南磷肥工业发展情况 ,提出对磷肥工业副产氟资源综合利用的设想 ,并介绍目前国内已有的一些氟资源综合利用的工艺技术     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

A broad line n.m.r. study of oriented poly(vinylidene fluoride)

Broadline nuclear magnetic resonance measurements have been carried out for the proton resonance in oriented poly(vinylidene fluoride). The spectra in general show two component lines with distinctly different line widths. The broad component shows a high degree of molecular orientation and can be satisfactorily assigned to the crystalline regions of the polymer. The narrow component corresponds to an oriented non crystalline phase which is sufficiently constrained to allow motion about the chain axis only. An appreciable decrease in the value of the rigid mass fraction was observed in both of the samples over the temperature range examined. Our calculations indicate that this could play an important role in the temperature dependence of the pyroelectric response of this material.     

十二酰胺丙基二甲基羟乙基氯化铵与十二烷基硫酸钠水溶液的表面吸附和胶束形成

利用十二酰胺丙基二甲胺和氯乙醇反应 ,合成了十二酰胺丙基二甲基羟乙基氯化铵 (DDHA)阳离子表面活性剂 ,将其与十二烷基硫酸钠 (SDS)以不同摩尔比进行混合 ,测定了混合系统的表面张力 ,计算了单一系统和混合系统的饱和吸附量、分子最小截面积 ,表面层和胶束中 DDHA的摩尔分率及分子间相互作用参数 ,目视观察了混合系统的浑浊情况。结果表明 :在降低γcmc和 cmc方面 ,DDHA SDS混合系统有协同效应 ,表面层和胶束的组成与二组分配比有关 ,但是非对称的 ,等物质的量混合物中 ,DDHA在胶束和表面层中具有较大的摩尔分数。DDHA与 SDS在实验测定的各混合系统中都不出现混浊     

Viscosity estimation for slags containing calcium fluoride

Based on recently published experimental data, the Riboud model was modified for viscosity estimation of the slags containing calcium fluoride. The estimated values were in good agreement with measured data. Reasonable estimation can be achieved using the modified Riboud model for mould fluxes and ESR (eletro slag remelting) slags. Especially for ESR slags, the modified Riboud model can provide much more precise values than the original Riboud model.     

Improvement of the deflocculating power of polyacrylates in ceramic slips by small additions of quaternary ammonium salts

In this work, we examine the effect of small additions of cationic quaternary ammonium salts (QAS) of different molecular weight on the rheology of an industrial ceramic suspension deflocculated with sodium polyacrylate and sodium metasilicate. The observed shear thinning behaviors obey the typical power law of fluid rheology. In order to characterize the rheological behavior of these slurries, three new parameters are introduced: a low shear rate consistency index and two transient viscosities, distant from the equilibrium, after increasing and decreasing the shear rates. These parameters vary with polyacrylate molecular weight and on additions of small quantities of QAS, which we found to be useful for decreasing the slurry viscosity.     

延迟破胶及强制裂缝闭合技术的研究及应用

采用延迟破胶技术,在压裂施工过程中加入不同浓度的胶囊破胶剂,利用它的延缓释放特性,使植物胶压裂液耐温、耐剪切稳定性增强,并且可以在不造成压裂液的流变性、滤失性和携砂性等过早丧失的前提下高浓度使用胶囊破胶剂。该技术与常规破胶技术相比,延缓释放率达50%,能更有效地清除液体残渣,减少压裂液对储层的伤害。同时由于有延缓破胶的特性,放喷采用相应的措施,可以降低支撑剂沉降速度,形成较好的沉砂剖面,提供高的裂缝导流能力,并且可以降低滤饼和压裂液残渣的伤害。     

浅谈降低电解槽氟化铝单耗的方法

氟化铝是电解生产中十分重要的原料，它对控制电解槽电解质温度，保持电解槽技术条件发挥着重要的作用。但随着电解生产成本的逐渐降低，氟化铝的消耗成为电解生产成本中的一项重要内容。本文就某分厂电解槽氟化铝添加的生产工艺、设备、控制以及管理等方面，提出降低氟化铝单耗的简要方法。     

真空钙热还原炉渣的综合利用研究

研究了从真空钙热还原炉渣中回收稀土的工艺条件；采用本工艺得到的合格稀土溶液，其回收率达65．41％；副产品氟化钙用作炼硅铁合金的助熔剂，使钙热还原炉渣得到综合利用。