济钢高炉喷煤数学模型的研究与应用

基于湍流两相流理论建立了高炉喷煤两相流动及传质三维数学模型。采用该模型指导高炉生产 ,高炉利用系数由2 .7t/(m3.d)提高到 3 .0 t/(m3.d)以上 ,焦比由 460 kg/t降到 40 0 kg/t,煤比达到 10 0 kg/t,提高了高炉的各项经济技术指标。     

Response of inertinites from some Australian coals to non-catalytic hydrogenation in tetralin

Inertinite concentrates from three Australian bituminous coals were hydrogenated at various temperatures ranging from 350 to 475 °C in the presence of tetralin without any added catalyst. Both conversion yields and microscopic observations of the benzene-extracted hydrogenation residues have revealed that the hydrogenation of the inertinite macerals becomes significant only > 400 °C, whereas the dissolution-hydrogenation of the accompanying vitrinite macerals occurs mainly between 350 and 400 °C. The major reaction pathway for the inertinite particles in the hydrogenation process appears to be one of initial mild carbonization followed by hydrogenation. A simplified reaction scheme is proposed which describes the reaction pathway involved in the hydrogenation of inertinite.     

Analytical pyrolysis as a tool for the study of plastic coals

The technique of analytical pyrolysis has been used to characterize 40 similar mid-rank western Kentucky coals of widely differing ASTM Gieseler plasticity. Certain pyrolysis/g.c. variables were shown to correlate well with both ASTM Gieseler and isothermal plasticity. Highly plastic coals were shown to exhibit certain characteristic peaks in the 450 °C pyrogram which were absent in the pyrogram of the non-plastic coals. Two coals, representing the two extremes in plasticity, were selected for further study. After extraction with solvents such as DMF the characteristic peaks were absent in the 450 °C pyrogram of the extraction residue of the highly plastic coal. These peaks were also shown to decrease with increasing severity of air oxidation of the plastic coal. This technique appears to be a useful tool for the analysis of mid-rank plastic coals and supports the view that the substances contained in the bitumen fraction of these coals are involved in the development of the plastic state.     

Emission of trace toxic metals during pulverized fuel combustion of Czech coals

A study of the trace elements emission (As, Se, Cd, Co, Cr, Cu, Zn, Hg, Tl, Pb, Ni, Sn, Sb, V, Mn and Fe) from pulverized coal combustion has been made at six heating and power stations situated in the Czech Republic. The amount of chlorine in coal has considerable influence on volatilization of some elements such as Zn, Cu, Pb, Hg and Tl, which is explained by the formation of thermodynamically stable compounds of these elements with chlorine. Generally, the affinities for Cl follows the order Tl > Cu > Zn > Pb > Co > Mn > Sn > Hg. The experimental data indicates enrichment of some of the trace toxic elements in the emissions (Cu, Zn, As, Se, Cd, Sn, Sb, Hg and Pb) and good agreement was obtained by thermodynamic equilibrium calculations with a few exceptions. In the case of Fe, Mn, Co, Cr and Sn calculated values are overestimated in the bottom ash and there are zero predicted amounts of these elements in the fly ash. In comparison, the results from experiments show up to 80% of these elements retained in fly ash. This implies that there exist additional steps leading to the enrichment by Fe, Mn, Co, Cr and Sn of small particles. Such mechanisms could include the ejection during devolatilization of small inorganic particles from the coal of bottom ash particles, or disintegration of the char containing these metals to small particles of fly ash. On the other hand, there are slightly overestimated or similar values of relative enrichment factors for As, V, Cu, Cd, Sb, Tl and Pb in the fly ashes and zero predicted values for bottom ashes. Our experimental results show about 5% or less of these elements are retained in bottom ashes, so they probably remain in the bottom ash inside unburned parts of coal. Copyright © 2003 John Wiley & Sons, Ltd.     

40kg试验焦炉的研制

文章介绍了40kg试验焦炉，分析和比较了试验焦炉与生产焦炉的差异，指出它们之间的模拟条件是炭化室宽度、煤料堆密度、炼焦速度和单向传热。     

本钢炼焦煤最佳配比分析

结合本钢的生产实际，对炼焦煤的最佳配比作了比较具体的分析，同时对资源，质量、成本也作了比较详细的调查，并提出了本钢焦化厂最佳配煤比方案，由此可看出，最大限度地降低采购成本，继续开发合理的配煤比例，具有广阔的前景。     

ATM网络的可用比特率业务

本文介绍了可用比特率业务的业务特点，速率控制机制以及该业务存在的问题。     

新疆三塘湖盆地侏罗系煤有机地球化学特征

有机地球化学和有机岩石学研究结果表明，新疆三塘湖盆地侏罗系煤中富集孢子体和角质体（３．０％～６．０％，全岩体积百分比），对煤中氯仿沥青“Ａ”组成中较高的总烃馏分（３０％～５０％）和饱芳比（０．６～３．０）产生了影响。煤的聚集环境是影响煤的显微组分组成及生油特性的关键因素。三塘湖盆地侏罗系煤属于“晚生晚排”叠加有“早生早排”类型的烃源岩。     

Verification of wind resource study of a Scottish region

In a survey of the practical wind energy resource present in the Tayside Region of Scotland it was estimated that over 1500 km² of land is suitable for wind energy development in the Region after consideration of a range of physical, technical and institutional factors. Wind speed data for this survey was obtained from the Energy Technology Support Unit (ETSU) UK Wind Speed Data Package. To verify the wind speeds obtained from the ETSU package a representative sample of sites in and around the identified areas of potential in Tayside were modelled for mean annual wind speed using the Wind Atlas Analysis and Application Program (WA^sP). The wind speeds for the sites obtained from the WA^sP analysis were compared with those obtained from the ETSU UK Wind Speed Data Package and conclusions drawn as to the reliability of the Tayside wind energy survey and the general applicability of the ETSU package for broad wind energy resource assessment.     

Apparent versus true density for the volume-to-weight transformation in coal blends

This work reviews the procedures involved in the conversion of the petrographic characterization data of blended coals into weight percentages of the single coals in the blends, the selection of the most suitable parameter for describing the density of the coals being critical. First, the fundamentals of the volume-to-weight transformation of the petrographic data were developed by means of mathematical formulae. This part of the procedure highlighted the need to use a density value adapted to the resolving power of the optical microscope. It was found that mercury penetration at 5 MPa, as determined by mercury porosimetry, was best suited for this purpose. A literature survey of published coal density data revealed that the use of correlations between coal density and rank was not an accurate enough procedure to deal with the relatively low corrections involved in the transformation of petrographic data. In the end, three binary blends were prepared from six carefully selected coals and polished particulate blocks of these blends were petrographically analysed to determine their compositions on a volume per cent basis. The best fit of these volume percentages with the weight percentages used in the formulation of the blends was found for a density correction based on mercury penetration at 5 MPa, in agreement with the empirical analysis.