加固改造中的结构承重体系转换

从加固改造工程的实践出发 ,探讨了混合结构向框架结构体系转换的方法和构造措施 ,为实际工程提供了新的技术思路     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

谈影响钻孔灌注桩承载力的因素

根据目前我国钻孔灌注桩的特点，从施工工艺方面，对控制沉渣、孔壁泥层过厚的问题进行了探讨，提出了合理、有效的措施，以确保桩基础承载力的正常发挥。     

含钡合金在钢液中的脱氧行为研究

在MoSi2炉上采用MgO质坩蜗对钢管进行了含钡合金脱氧行为的研究。实验中钡系合金主要选取SiAUBa、SiCaBa、SiAlBaCa、SiAlBeCaSr及用于钙处理的SiCa包芯线，选用Al作为对比脱氧剂，考察了钡系合金脱氧的全氧含量，脱氧产物的分布、尺寸和形貌，探讨了钡系合金脱氧和对夹杂物变性作用的机理。     

在湿陷性黄土地区对混凝土夯扩桩的检测

对夯扩桩在豫西湿陷性黄土地区的应用和可行性分析与检测。     

���þ��ܰ�ȫ�Բ�������������

本文通过对在用钻机井架的现场实际测试,建立数据库、测评模型,对实测的数据用计算机技术进行分析,提出了初始弯曲应力;数据正态分布检验——x～2检验;建立回归方程;在给定置信度下测评当前承载能力的技术概念。解决了在用钻机A型井架的安全性评估问题,是一种较为合理、可靠、科学的测评技术和方法。     

液压胀形轧辊油槽深度的确定

对液压胀形轧辊（即国外的ＶＣ轧辊）辊套热装后的弹性变形进行了有限元分析，给出了确定油槽最小深度的计算公式。本文的有限元计算结果与实验结果吻合，某些结论可为液压胀形轧辊的结构设计提供理论依据。     

叠轧薄板轧机轧辊轴承的改进

本文针对安阳钢铁公司薄板厂叠轧薄板轧机轧辊轴承轴瓦容易损坏、沥清润滑油冒烟起火这一问题，通过实验方法，找出了原因，并对大铜瓦进行了改进，取得了良好效果。     

精轧油膜轴承密封失效机理的初步分析

对油膜轴承密封出现的进水、漏油现象作了大量的调查、测量和统计分析，找出了产生质量事故的根本原因，提出了解决措施。     

D-10D磨煤机润滑油系统加装冷却器

针对鄂州发电有限责任公司磨煤机夏季轴瓦温度高，容易诱发烧瓦问题，进行深入分析，提出了多种解决方案，对各方案的可操作性及利弊进行了对比，选出了最佳方案并进行了实验，取得了明显的效果。