微重力落塔电磁悬吊、释放技术研究

论述了微重力落塔电磁悬吊、释放、提升机构的关键技术,电磁释放过程的特性分析以及微重力落塔实际试验的情况。分析说明:悬吊、释放性能的好坏决定了试验落舱的微重力水平,也是微重力落塔试验能否成功的关键技术。     

倾斜水塔的爆破拆除

针对某部倾斜水塔的定向爆破拆除,从防止水塔倾倒偏移和筒体触地冲击地面对周围环境造成影响等不利情况,确定爆破方案和采取相应的防护措施.     

36 m 高砖砌水塔定向折叠爆破拆除

介绍了复杂环境中砖砌高大水塔的定向折叠爆破拆除.根据周围的环境情况,在施工中采用了开定向窗、挖定位坑等技术措施,确保爆破成功,达到了设计效果.     

填料萃取塔的操作性能及设计计算

系统地介绍了填料抽提塔的两相流动及传质特性，设计计算，对填料塔的设计和操作有一定指导意义。     

单模光纤的传输衰减随温度变化的研究

本文从实验上测量了单模石英光纤在－50～120℃范围内的损耗。随着温度升高，光纤的损耗随之降低，在常温附近达到最小。其后损耗随着温度的继续升高而增加。损耗的变化主要是由于杂质的吸收和微弯损耗。本文对杂质的吸收以及微弯损耗进行了数值模拟，并且从理论上定性地解释了损耗对温度的依赖关系。     

Absorption of materials by or through the living skin

The skin comes into contact with a large range of materials either deliberately or inadvertently. It should be possible to predict the exact transport rates of these materials through the skin as a function of the physicochemical properties of the different compounds. With this sort of knowledge it is possible to predict the exact disposition of compounds and use this in the formulation of new products both in the pharmaceutical and cosmetic field. The information will also be useful from the standpoint of skin toxicology and environmental health. In order to be able to predict this complex process it is necessary to split the overall transport into different component parts. This article will identify these components and provide illustrations. The major areas discussed will be barrier function of the skin, the release properties of different topical formulations and how these may be monitored. Novel means of enhancing the penetration of drugs will be discussed and how some additives that are incorporated into formulations will perhaps alter the barrier function of skin. A mathematical model describing skin penetration has been developed and its use in predicting blood levels will be described. This model has been tested both in animal experiments and in limited human studies and its relevance to these situations will be highlighted.
Absorption cutanée et transcutanée in vivo     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

用稳态反饱和吸收法测量C_（60）的激发态吸收截面

用准连续激光实现了Ｃ６０的稳态反饱和吸收，通过实验和理论计算的拟合，确定了Ｃ６０的三重第一激发态吸收截面。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

Energy absorption in splitting square metal tubes

This paper presents an investigation into the energy absorbing behaviour of axially splitting square metal tubes. Tubes 50 mm square with a variable thickness were pushed slowly against rigid pyramid shaped dies, which had various semi-angles. By pre-cutting 5 mm long slits at the four corners, the tube splits along the corners and curls outward with a certain radius at a constant force. In this energy dissipating system, there are three components: tearing energy, plastic deformation energy and frictional energy. Theoretical analysis of the three energy components is presented. Curl radius is also studied in detail. Good agreement between experiments and theory is obtained. The results show that tubes which both split and curl may be used as efficient, long stroke energy absorbing devices.