Sulfuric acid recovery from rare earth sulphate solutions by diffusion dialysis

1 Introduction As an important industrial chemical, sulfuric acids are widely used in metallurgical and chemical processes, in which some waste solutions containing free sulfuric acids and metallic ions are therefore produced[1, 2]. If these waste acids …     

5%Si高硅奥氏体不锈钢元素偏析及均匀化处理

 高硅奥氏体不锈钢由于高含量硅元素的加入使其具有优异的耐高温腐蚀性能和较低的成本,在制酸行业有着潜在的应用价值。然而,该合金中高含量硅元素的加入会促进凝固过程中溶质再分配,进而造成显著的元素偏析,最终导致合金内部产生枝晶组织和大量的有害相。对铸锭组织进行均匀化处理能够有效消除枝晶与元素偏析,促进析出相回溶和枝晶消融,从而改善材料的热塑性,有效应对热变形开裂问题。因此,采用金相显微镜(OM)、扫描电镜能谱分析(SEM/EDS)、电子探针(EPMA)、JMatPro软件计算等方法,研究了实验室条件下制备的5%Si高硅奥氏体不锈钢铸锭的显微组织和元素分布状态,通过残余偏析指数、扩散动力学计算并结合均匀化处理试验验证,最终确定了5%Si高硅奥氏体不锈钢合理的均匀化处理工艺。结果表明,5%Si高硅奥氏体不锈钢凝固过程中钼元素偏析最为严重,通过残余偏析指数模型计算得到的均匀化动力学方程可用来指导该成分合金的均匀化处理工艺;5%Si高硅奥氏体不锈钢经过1 150 ℃×12 h均匀化处理后,铸锭内枝晶消融,元素偏析基本消除,析出相与铁素体回溶到基体中,合金转变为全奥氏体组织,热塑性得到改善;当加热温度达到1 250 ℃时,合金出现过烧现象,晶界开始熔化。     

Microstructural evidence for short-circuit oxygen diffusion paths in the oxidation of a dilute Ni-Cr alloy

A comparative study of high-temperature oxidation of Ni containing 1 at.% Cr and pure Ni was carried out. Instead of the conventional kinetics study using thermogravimetry, a microlithographic marker experiment was designed. Observation of the markers using cross-sectional TEM and SEM has revealed striking differences in the scale morphology, microstructures, and oxidation mechanisms between pure Ni and the Cr-doped Ni substrates. In particular, the results suggest that a small addition of Cr promotes significant inward transport of oxygen. Marker experiments revealed that NiO grown on pure Ni is wholly attributable to outward-cation diffusion. In contrast, NiO grown on Ni–1 at.% Cr exhibited formation of a substantial inner layer having a submicron grain size, established by the markers to have formed from oxygen ingress. For pure Ni, voids were observed to be distributed only within oxide grains. In contrast, for Ni containing 1 at.% Cr, elongated pores formed extensively along oxide-grain boundaries. Formation of new fine-grain oxide in these pores was observed to have sometimes completely resealed the void. It is, therefore, proposed that the transport of oxygen in the case of oxide scale grown on Ni–1 at.% Cr occurs via voids (pores) formed by vacancy coalescence at the grain boundaries.     

氯化铜在水溶液中的扩散系数的测定SCIEI

用膈膜池法测定了298K条件下CuCl_2在CuCl_2和CuCl_2-HCl水溶液中的扩散系数。发现CuCl_2的扩散系数与其浓度依赖性主要取决于它的化学位和溶液的粘度。     

预应变对16MnR钢断裂韧性的影响SCIEI

本文实验发现预应变对16MnR钢的断裂韧性具有显著的影响,断裂过程中裂尖区域材料的组织结构发生了变化,裂纹在二次珠光体组织上扩展。16MnR钢断裂韧性的大小取决于碳原子的扩散及二次珠光体组织生成的难易程度。     

HOMOGENIZATION TREATMENT OF Mg-Al-Zn(MM)MAGNESIUM ALLOY INGOTS

The Mg-Al-Zn series AZ31 and AZ31 MM alloys are homogenized at 673, 723 and 753K respectively. The hardness of alloy ingots at different heat-treated states is measured and the micro structures are observed. The optimum annealing temperature is 723K and the time is 12h.     

Magnetic and mechanical properties of FeSi alloys with high Si content

The chemical vapor（CVD） deposition-diffusion method was applied to prepare FeSi alloys with high silicon content up to 6.5%. In spite of various deposition and post-annealing, the sample remains α-Fe bcc structure. The cross section of the composition was analyzed to evaluate the Si content and distribution before and after annealing. The results show that the soft magnetic properties are improved by increasing the silicon content. For the samples containing about 6.5% Si, the coercivity decreases to 60 from 237.3 A/m of the original. It is also obtained that, in addition to the Si content, Si distribution has a large influence on the core loss due to the effect of resistivity. The micro-hardnesses were also evaluated along the cross-section after various annealings.     

镁合金与钛合金的瞬间液相扩散焊

为实现镁合金AZ31B与钛合金Ti6A14V的可靠连接，研究了两者以Al为中间层的瞬间液相扩散焊接头的微观结构与连接强度。研究结果表明：当焊接时间为180min时，焊接温度是影响界面反应热力学与动力学的主要参数，其对接头的微观组织、接头界面新生相构成与连接强度有重要影响。保温温度低于450℃时，AZ3IB／AI界面无液相产生，无法实现AZ31B与Ti6A14V的可靠连接；保温温度在450℃～480℃变化时，温度对AZ31B／Al／Ti6A14V界面反应的动力学因素有明显影响，且直接决定了焊后接头新生相的构成与分布。470℃保温180min的接头剪切强度较高（72．4MPa），达到AZ31B母材（86MPa）的84．2％。     

定向凝固法制备YBC超导体的若干材料学问题

讨论了定向凝固法制备YBCO超导体涉及的包晶转变与包晶反应，成分过冷，扩散控制生长模型，界面效应及定向凝固YBCO生长晶体学等问题。     

Low-melting-point titanium-base brazing alloys—part 2: Characteristics of brazing Ti-21Ni-14Cu on Ti-6Al-4v substrate

Filler metal of a low-melting-point (917 °C) Ti-21Ni-14Cu was brazed onto the substrate of Ti-6Al-4V alloy at 960 °C for 2,4, and 8 h to investigate the microstructural evolution and electrochemical characteristics of the brazed metal as a function of the period of brazing time. Optical microscopy, scanning and transmission electron microscopy, and x-ray diffractometry were used to characterize the microstructure and phase of the brazed metal; also, the potentiostat was used for corrosion study. Experimental results indicate that diffusion of copper and nickel from the filler metal into the equiaxed a plus intergranular β structure of Ti-6Al-4V substrate causes the lamellar Widmanstätten structure to form. The intermetallic Ti₂Ni phase existing in the prior filler metal diminishes, while the Ti₂Cu phase can be identified for the metal brazed at 960 °C for 2 h, but the latter phase decreases with time. Advantage might be taken from the evidence of faster diffusion of nickel than copper along the β phase to the substrate. In deaerated Hank’s solution, corrosion potential, corrosion current density, and critical potential for active-to-passive transition decrease while the passivation range broadens with the period of brazing time. However, all the brazed metals, immersed for different periods in oxygen-saturated Hank’s solution, show similar corrosion behavior, irrespective of the brazing time.