尿素分解加热器清洗剂的研制和应用小结

针对一分加污垢的特点，通过实验，研制了以有机酸为主要成份的尿素分解加热器清洗剂及清洗工艺，并进行了４台次加热器的清洗，取得了较好的效果。此清洗方法具有工艺简单、安全、分析控制容易、费用低廉的特点。     

粗品四氢呋喃的除醇与抗氧化技术

介绍了粗品四氢呋喃的除醇技术，过氧化物的生成机理与抗氧化技术。     

电除尘器绝缘子的设计与选择

根据电除尘器绝缘子的功能、工况条件等特点，分别从材质、外形尺寸等方面介绍了设计和选择的注意事项。为用户合理地选择电除尘器绝缘子提供了帮助。     

高效节能水力旋流器研究进展

综合介绍了国内外高效节能水力旋流器的研究进展,分析了影响旋流器分离性能和能耗的主要因素,介绍了针对不同问题提出的相应解决办法.对其迄今的研究成果进行了简要评述,并对其发展进行了展望。     

炭素厂的消烟除尘和噪声控制

针对炭素制品生产过程产生的粉尘、沥青烟气、噪声等主要涉及工业卫生及环境保护等方面的问题进行剖析，并对治理方法做了简要的介绍。     

Efficient material design for diesel particulate filters

This paper will give an overview about the filter development for diesel particulate emission control in automotive applications. The material development for passenger car diesel particulate filters led to new materials like silicon carbide while for heavy duty applications still Cordierite plays a major role. But in the future other materials might also be used for passenger cars. This paper will show the basic difference between both applications and describe the material design in terms of filter properties (base material, back pressure aspects, filtration efficiency, coating impact). Current application on vehicles with catalysed soot filters (CSF) with and without oxidation catalyst will be presented. Furthermore an outlook will be given on materials for catalysed soot filters for the future.     

低(等)压合成氨的最佳H2/N2与催化活性的关系

采用高压催化剂性能评价实验装置，在压力分别为7.0,10.0和15.0MPa，温度分别为350,400和450℃条件下，在H2／N2为1.6-3.0范围内研究了H2／N2对A301，ZA－5和A110－2型催化剂的活性和合成塔出口氨浓度的影响。在压力和空速一定的条件下，最佳H2／N2随反应温度而异。在350，400和450℃下，最佳H2／N2分别为1.8-2.2,2.2-2.5和2.5-3.0。由此可见，合成氨反应的速率达到最大值时的最佳H2／N2值与反应的进程有关。为此提出了催化剂效率K（Catalysis efficiency)的概念来表征在催化剂作用下反应器出口氨浓度趋近平衡的程度，即K＝CNH3／C^*NH3。根据实验结果，得到了最佳H2／N2与催化剂效率的定量关系：（H2／N2）m=1.5(1 CNH3/C^*NH3)=1.5(1 K)。由此可以根据催化剂在不同反应条件下的催化剂效率来确定最佳H2／N2。凡是会降低催化剂效率的因素，都会使最佳H2／N2降低。各种影响因素对最佳H2／N2的影响中，反应温度的影响最大，其次是空速和催化剂的活性，而压力和惰性气体含量的影响相对较小。在低温（低压）下合成氨，宜采用较低的H2／N2。     

黄磷的物理法脱砷新方法探索研究

针对我省黄磷精制现状,研究一种黄磷除砷新方法。利用高压静电场对工业黄磷进行处理,结果显示:在电场的作用下能分离除去砷,经三级处理脱砷率可达90%以上,黄磷回收率在99.9%以上。简要介绍了此处理方法的原理及工艺。     

浅谈燃气轮机的清洗方法

由于燃气轮机吸收含有大量灰尘等杂质的空气,会在压气机叶片上形成积垢,从而导致机组出力下降,该文介绍在实际工作中,根据不同的情况使用不同的设备、采取不同的清洗方法来除去压气机叶片上的污垢,以提高整台机组的工作效率.     

Increasing urea-N efficiency for transplanted lowland rice by pneumatic injection: Yield and economics at the farm level

To increase the fertilizer-N efficiency in lowland rice (Oryza sativa L.) cultivation, new management practices are needed. Main cause of the present low efficiency is the low N recovery by plants, as a considerable part of the N applied is lost; deep placement techniques improve the recovery. A pneumatic injector, with which urea prills can be point-placed at a depth of 5–10 cm in paddy soils, was tested in 38 on-farm trials in 1989/90, mostly during the wet season. The experiments, located in Africa and Asia, focussed on differences in grain yield between conventional methods of broadcasting urea and injection by the pneumatic injector, at recommended N-rates. The study shows that the pneumatic injector is effective as a tool to improve the N fertilizer efficiency. The average yield increases per region, resulting from the use of the injector, ranged from about 250 to 1300 kg grain ha^–1. The value of the yield increase would allow most farmers to recover the costs of the injector within one season, even if labour was hired to carry out the injections. The average labour requirement of the injector was 40 hours ha^–1. In Indonesia, injection of prilled urea gave yields similar to those obtained with urea briquettes.