Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

暖通空调工程设计常见问题

通过对施工图审查工作进行总结，指出了暖通空调和防火防排烟设计中存在的问题及防火规范本身的一些不足。     

Structure and dynamics of dipolar fluids under strong shear

Molecular dynamical simulation has been carried out to investigate the structure and dynamics of a dipolar fluid under strong shear. Dipolar fluid consists of polarizable particles, which have an induced dipole moment in the applied field direction. Shear stress is perpendicular to the field direction. When shear stress is small, the flow has a flowing-chain structure. If shear stress increases to pass a critical value, flowing-chain structure changes to flowing layer structure. Each layer is parallel to the flow direction and shear direction. Within one layer, particles form strings in the flow direction.     

人支气管上皮靶细胞形态学参数的测量

支气管上皮靶细胞形态学参数对计算受氡子体照射的支气管的剂量是很重要的。本文介绍利用奥尔新兰-PAS 染色的外科切除人肺组织切片,测量基底细胞粘液细胞和的胞核深度与数目。结果表明,叶、段和小支气管的粘液细胞核深度分别为相应节段基底细胞的61%、69%和73%;此三节段粘液细胞的数目分别为基底细胞的53%、29%和28%,平均为37%。     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

Stable Oxygen and Carbon Isotopic Compositions of Lates stappersii Otoliths from Lake Tanganyika,East Africa

In this study, we measured growth trends in oxygen and carbon isotopic ratios in whole sagittal otoliths from three adult centropomid fish (Lates stappersii) from each of three sub-basins of Lake Tanganyika, East Africa. Sampling density was 20 to 50 samples per otolith. Both δ¹⁸O and δ¹³C values increase with age. The δ¹⁸O data suggest that otoliths were precipitated near the expected equilibrium with the ambient environment (ca. +3.5‰) and support a migration pattern from surface waters during larval stages to deeper waters (40 to 80 m) for mature fish. Relatively high δ¹⁸O values in the southern sub-basin are consistent with cooler temperatures in the region during seasonal upwelling. The δ13C increase from otolith core to edge is large (up to 4‰) and is interpreted as due to ontogenetic changes in diet and contributions from a decrease in the proportion of respired CO₂ incorporated into otolith carbonate as metabolic rates of the fish dropped with maturity. The data seem to successfully reveal life strategy and migration patterns of L. stappersii, document regional differences in lake conditions, and provide a record of temperature within the water column during which the fish lived. Higher resolution studies and analyses of historical samples could be used to constrain modern and past growth patterns, and to reconstruct past temperature gradients and productivity patterns in the lake.     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。