汽车摩擦片厚度测量装置驱动电路的研究

本文通过对摩擦片厚度在线测量装置系统构成的全面分析，对其驱动电路子系统进行了理论探索和技术研究，完成了相应的电路设计、误差分析及器件选择等工作，并进行了具体的实验验证，证明该驱动电路具有良好的性能，可圆满实现摩擦片厚度在线检测和实时分析的工作任务。     

Low Temperature Elastic Constants of Polycrystalline MgB2

We have used a resonant ultrasound spectroscopy technique to measure the bulk and shear modulus of fully dense, polycrystalline MgB₂ between 4 and 300 K. Both moduli show good agreement with published first principle calculations. The internal friction shows a broad maximum around 40 K.     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.     

Relationship between Relaxation Internal Friction Peak at about 200℃(f≈1Hz)and Bainitic Transformation In a CuZnAl Alloy

The present investigation showed that the re-laxation peak at about 200℃ (f≈1Hz) was relatedto bainitic transformation in a CuZnAl alloy.Thepeak decreased when bainite precipitated.Theactivation energy of the peak was the same as theapparent activation energy of bainitic transforma-tion.According to the relations between the peakand the bainitic transformation,the mechanism ofthe peak has been discussed.     

适用于稠油开采的游梁式抽油机设计分析

在稠油开采中,抽油杆在液体中运动时,所受到的摩擦阻尼力很大,有时高达几十千牛。上冲程时,该力有加大悬点载荷的作用;下冲程时,该力使抽油杆下行困难,甚至悬点载荷为零。为了开采稠油,必须根据其特点设计适应的游梁式抽油机。文章分析了稠油用抽油机的受力特点,提出了该类抽油机的设计要求。     

双组分树脂冷压法制备摩擦材料

研究甲、乙双组分液体树脂作为粘结剂制备制动摩擦材料的冷压工艺方法，甲组分树脂为硼改性腰果壳油树脂，乙组分树脂为三聚氰胺改性酚醛树脂。该工艺可使模压料在室温下具有良好的成型效果，在固化处理中不使用夹具，可以使成型料具有良好的保型效果。冷压制备的制动摩擦材料具有硬度低、摩擦系数稳定和恢复性好等特点。     

二硫代磷酸硫化氧钼与硫,磷添加剂的复配特性研究

研究了二烷基二硫代磷酸硫化氧钼（ＭｏＤＴＰ）摩擦改进剂及其与硫、磷、硫－磷型添加剂复合的抗磨减摩性能。试验表明，经过适当复配后，这类合活性元素的添加剂对ＭｏＤＴＰ的抗磨减摩性能均有增效作用，同一类型添加剂的活性愈高，增效作用愈显著。同时利用扫描电镜和Ｘ－射线能谱仪进行摩擦副表面膜的形貌照相及元素分析，对复合作用的机理进行了初步探讨。     

Finite element simulation of the mechanics of flat contact pad fretting fatigue tests

An understanding into the macro kinetic and kinematic behaviour of fretted surfaces is provided. Making use of a modified version of a previously developed in‐house two‐dimensional elastic–plastic finite element analysis numerically simulates flat contact pad fretting fatigue tests. Basic macro mechanics concepts are adopted to idealise two bodies with rough contact surfaces and loaded at two different sites with arbitrary axial loading profiles. A time scale factor is devised to recognise the earliest candidate out of the events possibly accommodated at each loading increment. The present analysis utilises a relevant experimental set up developed in the Structural Integrity Research Institute of the University of Sheffield as an application. Computational results accurate to within 1.2% and corresponding to one contact pad span and six constant normal loads acting individually with four amplitudes of two sinusoidal axial load cycles are presented. The present computations include (1) the development of the global and local normal and tangential reactions and relative sliding displacement acting along the fretting surfaces and (2) contact pad deformation, generated stress fields and plasticity development within the neighbouring region of the fretted area.     

Increasing the precision of a device used to determine the dynamic coefficient of friction

A theoretical evaluation of the potential application of a device with inclined plane for determining the dynamic coefficient of friction is given. Structural changes in the device that make it possible to increase its precision are proposed. Computational equations for estimating the resolution of the device are presented. __________ Translated from Izmeritel’naya Tekhnika, No. 11, pp. 24–26, November, 2007.     

海流涡激效应对钻井隔水导管疲劳强度的影响

钻井隔水导管是从海上钻井平台下到海底浅层的套管,在海上钻完井过程中起着非常重要的作用。在深水海域,由于隔水导管泥线以上长度的增加,海流对钻井隔水导管疲劳强度影响作用加剧,从而影响隔水导管的使用寿命。开展海流涡激效应对钻井隔水导管疲劳强度影响研究,能够为钻井隔水导管尺寸和材料选择提供科学依据。文中对隔水导管进行了力学分析,将隔水导管受力模型简化为下部固定,上部简支的梁模型来分析。利用流体阻尼及流体涡激力理论模型,计算海流作用下涡激效应对于隔水导管疲劳强度的影响。结合南海某海域的海况资料,对海上钻井隔水导管的疲劳强度和使用寿命进行了分析和校核,给出了该海域合理的隔水导管尺寸。通过研究得出:随着水深的增加,海流对隔水导管的涡激效应会逐渐加强,对隔水导管疲劳强度影响加剧。