注射成形粘结NdFeB磁体:工艺·性能·应用

综合介绍了几种适于注射成形粘结NdFeB磁体的磁粉制备方法及特点；讨论了粘结剂、改性剂及磁场取向对注射成形NdFeB磁体最终磁性能的影响及其应用市场。在此基础上，指出了今后开展研究工作的方向。     

济钢高炉喷煤数学模型的研究与应用

基于湍流两相流理论建立了高炉喷煤两相流动及传质三维数学模型。采用该模型指导高炉生产 ,高炉利用系数由2 .7t/(m3.d)提高到 3 .0 t/(m3.d)以上 ,焦比由 460 kg/t降到 40 0 kg/t,煤比达到 10 0 kg/t,提高了高炉的各项经济技术指标。     

大功率开关电源的设计与实现

介绍了开关电源设计中需要考虑的几个基本问题,包括频率的确定、最大占孔比Dm的确定、逆变变压器的设计和开关功率管的选择,并以一种1 kW的PWM大功率半桥式开关电源为例,详细介绍实际的开关电源设计方案,并给出了实验结果.     

Investigation on vapor-cooled current leads operating in a pulse mode

This paper describes transient numerical modeling for thermal characteristic of vapor-cooled current leads under pulse operation. The transient thermal analysis considers the temperature difference between a helium gas flow and a copper lead with temperature dependent properties of helium gas, copper and stainless steel. The numerical analysis was validated by an experiment with commercially available 100 A vapor-cooled current leads. A proper overloading factor calculation and the effect of intermediate cooling are presented for the current leads under pulse operation, which can significantly reduce heat input to a cryostat.     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

一种基于PWM的半桥型开关电源

主要介绍了由SG3525组成的半桥型开关稳压电路的结构和工作原理，阐述了PWN集成电路SG3525的特性和主要功能。实践表明：该系统工作稳定，运行效果良好。     

流动注射分光光度法测定钴

研究了将ＰＡＮ用于流动注射（ＦＩＡ）分光光度法测定微量钴，在５６０ｎｍ处绘制标准曲线，线性范围为０～４５μｇ／ｍｌ，相关系数０．９９６，方法的相对标准偏差（ＲＳＤ）小于３％，加标回收率为９５％～１０５％，进样频率８０次／ｈ。本法简单快速，用于面粉、分子筛，铝合金测定结果令人满意。     

实验应变／应力模态分析若干问题的进展评述

本文评述了实验应变／应力模态分析进展的若干基本问题。主要是：应变响应与位移响应的关系；应变频响函数矩阵的特点及其测量方法；应变模态的加权正交性及其识别方法；以及其他问题。     

注聚采出水分离用动态水力旋流器特性研究

原有的地面工艺和设备已不能满足聚合物驱采出水分离的要求。采用自行研制的动态水力旋流器，在增压与不增压两种工艺流程下，分别进行了流量和转数对分离效率的影响、转数与压力降的关系，以及入口压力与处理量的关系等项试验研究。试验结果表明，与静态水力旋流器相比，动态水力旋流器的分离效率明显提高，一般可提高10％左右；压力损失显著降低，约可减少0．1MPa，足见可在低压下工作，易于实现无泵运行；无泵运行明显比有泵增压运行的分离效率高，但处理量会有所降低。将动态水力旋流器应用于聚合物驱产出水的油－水分离处理是完全可行的。