具有厚大断面的大型球墨铸铁铸件的生产

首先通过电炉—LF精炼炉—VD精炼炉—包内球化的工艺路线获得了足够的优质铁液,然后通过选取合适的分型面、设置合理的浇注系统、设计专用的冷铁、安放足够大的保温冒口和上表面加大加工余量来去除夹渣等措施,成功生产了具有厚大断面的大型球墨铸铁铸件。     

摩擦诱发高铬铸铁相变的透射电镜研究

利用透射电子显微镜研究了高铬铸铁在摩擦过程中的显微组织变化。结果表明：奥氏体基体在摩擦应力的作用下发生相变。摩擦表面形成α‘Ｍ。次表层形成γ与α’Ｍ共存区；γ与．ε共存区；γ位错丛聚区。     

高炉炉缸内铁水环流与内衬侵蚀

从分析中心焦柱在炉缸内的受力出发，计算了１０００￣５５８０ｍ＾３高炉大喷煤前后中心焦柱在炉缸铁水内的沉入深度，分析了炉缸内铁水环流的产生与炉缸内衬侵的关系，分析表明大喷煤有得利抑制铁水环流对缸内补的冲刷，提出了降低铁水环流对炉缸内衬侵蚀的途径。     

以1,3-二(4-邻羟基苯亚胺次甲基)苯氧基丙烷为载体的铁离子(Ⅲ)电极的研究

以1,3-二(4-邻羟基苯亚胺次甲基)苯氧基丙烷为中性载体制备了PVC膜Fe3+离子选择性电极。该电极对Fe3+呈现出良好的选择性和近Nernst电位响应性能。电极斜率为21mV/dec,线性范围为3.0×10-5～1.0×10-1mol/L,检出限为1.0×10-5mol/L。采用交流阻抗技术研究了电极的响应机理,并将电极作为指示电极初步用于EDTA的电位滴定。     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.     

DD—921钢铁常温发黑剂的研制和应用

研究了钢铁常温发黑过程的成膜机理,各组分之间的作用以及相互之间的影响,着重分析了常温发黑的优缺点,工艺控制参数以及经济性。     

铸铁在700℃时氧化过程的观察

利用光学显微镜、电子探针以及扫描电镜研究了灰铁、球铁和蠕铁在７００℃时的氧化过程。结果表明：（１）灰铁的氧化主要沿石墨与基体的相界面进行，初生奥氏体枝晶对氧的侵入具有一定的阻碍作用；（２）球铁是沿晶界比先氧化来实现其间接氧化的；（３）蠕铁氧化的模式主要取决于蠕化率的高低。     

热压变形对灰口铸铁石墨形态的影响

研究了灰口铸铁(HTl50)在900℃大压下量塑性变形后石墨的分布形态，结果表明：随着压下量的增加，石墨片逐渐趋于平行分布；变形过程中发生了碳的回溶，同时伴随着石墨片的断裂；石墨片体积分数及片间距随压下量的增加而逐渐减少。     

提高高铬白口铸铁磨球冲击抗力的技术关键

当高铬白口铸铁含铬量为18%～28%,Cr/C值是8￣9,铸铁的显微组织是回火马氏体 少量残余奥氏体(<5%) M7C3碳化物,则磨球具有高的冲击韧性和断裂韧性K1C,具有高的冲击抗力,表现出低的冲击剥落量。     

Mössbauer studies of iron-bearing minerals in coal and coal ash

⁵⁷Fe Mössbauer spectroscopy has been used to characterize the iron-bearing minerals present in some British Columbia coals. The minerals observed in a range of samples include pyrite/marcasite, siderite, jarosite, rozenite or melanterite, and Fe²⁺ -bearing clay minerals such as illite. The presence of jarosite is confirmed through the magnetic hyperfine interaction observed at 4.2 K. The absence of magnetic ordering at 4.2 K for the ferrous sulphate component indicates the presence of rozenite, FeS0₄ · 4H₂0, or melanterite, FeS0₄ · 7H₂0, rather than szomolnokite, FeS0₄ · H₂0 or FeS0₄. The effects of ashing on two of the coals is also studied.