基于延迟捕获功能的血液切变率测量方法

对延迟捕获的基本原理进行了系统的分析,详细介绍了利用延迟捕获功能实现计时计数法测量转速的具体方法和实例.此方法已应用在粘度测试仪器中切变率指标的测量上,经实际使用表明具有软硬件结构简单、成本低、精度较高、运行可靠等优点,对于一些在嵌入式应用中需要测量转速指标时,可谓一种良好的方法.     

A study of the large strain deformation and failure behaviour of mixed biopolymer gels via in situ ESEM

A mixed biopolymer gel, consisting of a protein (gelatin) and polysaccharide (maltodextrin) mixture has been investigated. By controlling the composition it was possible to construct an ‘emulsion-like’ structure, with included spherical particles of one phase (maltodextrin) within a continuous matrix of the second (gelatin). Large strain deformation and failure behaviour of this system has been examined via in situ environmental scanning electron microscopy (ESEM). ESEM has been employed to explore the changes in the structure of the material, whilst allowing the sample to stay hydrated as it was subjected to tensile strain, thereby allowing simultaneous imaging and determination of stress-strain data of the native sample. Ductile behaviour was observed, which has been attributed to the stretching, tearing and fracture of gelatin ligaments and debonding at the interface between the maltodextrin particles and continuous gelatin matrix. Deformation and fracture of the maltodextrin particles during tensile testing was also observed. The interfacial fracture energy of the composite has been calculated following an elastomer composite-debonding model, although there are several limitations to this approach for the mixed gel. It was found in samples tested after different ageing times that the debonding stress and strain was decreasing with ageing leading to a lower interfacial fracture energy. Samples were also tested after successive loading cycles, which resulted in a mechanical strength decrease after each cycle.     

Efficient and accurate approach for powder compaction problems

 In this paper, a new approach for powder cold compaction simulations is presented. A density-dependent plastic model within the framework of finite strain multiplicative hyperelastoplasticity is used to describe the highly nonlinear material behaviour; the Coulomb dry friction model is used to capture friction effects at die-powder contact; and an Arbitrary Lagrangian–Eulerian (ALE) formulation is used to avoid the (usual) excessive distortion of Lagrangian meshes caused by large mass fluxes. Several representative examples, involving structured and unstructured meshes are simulated. The results obtained agree with the experimental data and other numerical results reported in the literature. It is shown that, contrary to other Lagrangian and adaptive h-remeshing approaches recently reported for this type of problems, the present approach verifies the mass conservation principle with very low relative errors (less than 1% in all ALE examples and exactly in the pure Lagrangian examples). Moreover, thanks to the use of an ALE formulation and in contrast with other simulations, the presented density distributions do not present spurious oscillations. Received: 20 March 2002 / Accepted: 15 October 2002 The partial financial support of the Ministerio de Ciencia y Tecnología (grant number DPI 2001-2204) is gratefully acknowledged.     

铜镍锰钴应变电阻合金的研究

为解决我国箔式应变计引进生产线用箔材国产化的问题，本所自行设计研制了一种新型的温度自补偿铜镍锰钴合金。该合金具有良好的性能复现性和工艺稳定性，制片后的各项性能十分优异，特别是其平均热输出系数Ｃｔ和对试件材料的适应性明显优于进口箔，是制造高精度箔式应变计的理想材料。     

NiTi形状记忆合金基本驱动特性

研究了预应变ＮｉＴｉ形状记忆合金的基本驱动特性，结果表明，加热和冷却过程回复力存在滞后行为；卸载过程中应力与应变具有与加热、冷却过程相关的非线性关系；卸尖力随卸载应变速率增加而降低，此外研究了预应变ＮｉＴｉ合金丝产生回复力后对外应力的响应行为。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

重力坝深(底)孔断面钢筋混凝土模型试验研究

文通过7个小尺寸和1个大尺寸的钢筋混凝土断面模型试验，研究重力坝深(底)孔在坝体自重和内水压力以及超内水压力作用下的结构特性和破坏规律。重点探讨混凝土和钢筋应力应变、混凝土开裂、裂缝宽度和裂缝扩展规律，为建立更为科学的孔口配筋理论提供依据。     

无间隙原子钢的微观结构特征和塑性应变比

采用Ｘ射线衍射的ＯＤＦ和ＬＰ分析技术，ＳＥＭ电子通道花样和蚀坑技术观测，研究了超深冲无间隙原子钢板的微观结构特征。结果表明：控制化学成分、保证基体纯净、优选工艺参数，促进强的γ－〈１１１〉∥Ｎ．Ｄ纤维织构的形成是获得优异成型性的关键。用ＣＭＴＰ方法，由ＯＤＦ织构数据从理论计算了塑性应变比（ｒ），表明ｒｍ值高达３．１８。文中讨论了再结晶织构形成机制。     

水闸闸室化算梯形横截面上不平衡剪力的分配计算

当地弹性地基梁法计算非岩石地基的水闸底板应力时，首先要求解出不平衡剪力，当闸墩截面选择梯形时（主要是边墩），常用方法是作图法，这既有误差又繁琐。所以就此推导出一个公式，可直接求解平衡剪力。     

一种新的基于极大似然估计的系统辨识方法

进化计算是一种基于自然选择和自然变异机制的并行随机优化算法。由于递推极大似然估计法难以实现性能指标函数的全局寻优，所以本文提出了将改进的进化计算用于系统参数辨识的方法。计算机仿真结果表明，该算法能够实现似然函数的全局寻优。