论剪切质量的提高

通过对飞剪剪切长度，精度，剪刃间隙和压板机构等参数的优化，来提高钢板的剪切质量。     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

弹力竹节牛仔布织造工艺优化

介绍了弹力竹节牛仔布的生产工艺 ,同时对KT36 8剑杆织机织造该织物的工艺进行了优化研究     

Axial vibrations of U-shaped bellows with elastically restrained end conditions

Previous work by Li et al. in the area of axial vibrations of bellows dealt with fixed end conditions. However, it is seen on several occasions that bellow ends are welded to a small pipe spool that has a lumped mass such as a valve or an instrument. Hence, the present paper aims at finding out the effect of elastically restrained ends on the axial natural frequencies. The analysis considers finite stiffness axial restraints on the bellows, i.e. solving the set of equations with non-homogeneous boundary conditions. Two bellow specimens are considered for comparison having the same dimensions as taken by Li in his analysis. The transcendental frequency equation deduced is accurate as the first, second and third mode frequencies computed are in close agreement to the ones obtained by Li.     

基于显微视觉的宏/微双重驱动微动台的自动标定

提出了基于压电技术的微操作系统的自动标定方法,采用混合式步进电机直接驱动的宏动平台,实现系统大行程宏动定位,安装在宏动平台上的压电陶瓷驱动的微动平台和精密光栅,实现亚微米级的分辨率和定位精度,通过以上两部分实现定位机构的全闭环反馈控制,采用显微视觉反馈获取微动台操作器在图像中的位置信息进行标定。实验结果表明:系统的动态和稳定性能良好,自动标定运算速度快,运行速度达到11 frame/s,实现了对系统的精确标定,标定精度达到0.1μm。     

选择性控制技术在TRT系统中的应用

为了解决高炉顶压生产短期内处于不正常的情况,即不使TRT系统停车而又起到对生产进行自动保护的目的,山东莱钢TRT系统对旁通阀采取了选择性控制技术。该技术的应用稳定了高炉炉顶压力,既保证了安全生产,同时增加了经济效益,在国内TRT行业极具推广意义。     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.     

快速色谱分析技术在油气勘探中的应用

文章通过对五口井的现场应用介绍，阐述了快速色谱分析技术在油气层识别和解释方面的准确性，探讨了该技术在薄油气层的发现和评价、快速钻进条件下油气层的发现、对油气层全烃组份变化的统一、水平井的地质导向以及排除钻井液添加荆对油气显示的影响五个方面的优势，从而论证了快速色谱分析技术在油气勘探中的应用价值。     

厦门市筼筜湖城市防汛排涝现状及其对策

本文通过分析筼筜湖的自然概况、防汛排涝系统设施及实际运行等资料,提出进一步提高筼筜湖防汛排涝能力的对策。