Time‐dependent heat transfer coefficient of a wall

A time‐dependent coefficient of heat transfer is proposed for the computation of thermal power required, so that a room temperature reaches a desired value within a given time. A mathematical formulation of the room heating transient phenomenon is constructed in a dimensionless form. Using an integral approximate solution an analytical expression for this coefficient is provided and it is verified by diagrams adopted by DIN 4701. Copyright © 2003 John Wiley & Sons, Ltd.     

Matrix mediated alignment of single wall carbon nanotubes in polymer composite films

Alignment of single wall carbon nanotubes (SWNT) in liquid crystalline (LC) polymer matrix imparting orientation to the nanotubes along the nematic director was studied by atomic force microscopy, measurements of electrical conductivity and Raman spectroscopy of the composite in the directions parallel and perpendicular to the nematic director. The composites were prepared through dispersion of SWNT with LC monomer in a common solvent, their alignment in nematic monomer and consequent UV polymerization of the monomer. The anisotropy of electrical and optical properties of the system depends strongly on the concentration of the nanotubes in the range of 1-10% SWNT being especially strong for smaller concentrations and negligible at higher loads. A simple semi-quantitative model is suggested to account for the orientational behavior of nanotubes in nematic matrices. It successfully describes the observed anisotropy of physical properties at microscale (up to 200 μm) in terms of anchoring of the polymer chains to the nanotubes surface and adjustment of the nanotubes orientation to the nematic direction due to such coupling. The increasing disorientation of the nematic domains at higher nanotubes loads is explained as a development of larger number of LC defects induced by the nanotubes in the nematic matrix due to their intrinsic nature of aggregation. The anisotropy of physical properties at macro scale (several millimeters) is much smaller and less dependable on SWNT concentration because differently oriented LC domains effectively wash out the anisotropy.     

铝合金穿孔板吸声墙面施工技术

以教育部综合办公楼工程的机房铝合金穿孔板吸声墙面施工为例,介绍其固定件及吸声墙面的做法。     

管道内壁阴极保护技术

阴极保护技术已广泛应用于管道的外防腐,而在管道的内防腐中还存在只适用于大口径管道、保护距离短、阳极与管道内壁绝缘难、安装复杂等问题。为此,江汉油田设计院开展了管道内壁阴极保护技术研究工作。试验证明,管道内壁采用强制电流和牺牲阳极阴极保护完全可行,用在柔性阳极或带状锌合金、铝合金牺牲阳极上外套打孔塑料管或塑料网的安装方式成功地解决了管道内壁阴极保护存在的上述问题,具有适用范围广、施工工艺简单、经济方便等优点。文章着重介绍了塑料套管或塑料网阳极安装方式及其模拟试验、现场试验的条件和结果。     

土体中毛细水压力的研究

该文从毛细水产生负孔隙水压力概念入手 ,对较难确定的孔隙水压力系数以及较抽象的地下连续墙时效稳定分析等问题进行了定量计算 ,以期对工程实践有一定的指导作用     

阿曼Daleel油田分支井钻井液技术研究

对Daleel油田作业5区三分支水平井DL-59井井下复杂情况分析,室内测定了引起复杂情况的Nahr Umr泥页岩地层的矿物组分和粘土矿物含量,优选了适应在该泥页岩地层215.9 mm造斜井段的钻井液配方中的各种处理剂,最后研制出钻井液配方,通过DL-73井应用后,取得了良好的防塌效果.     

格栅式水泥搅拌桩支护在西涌泵站的应用

简介水泥搅拌桩的支护机理,以西涌泵站为例介绍采用格栅式水泥搅拌桩作支护结构的设计及计算方法,指出该技术能较好地解决软湿粘性土地区枢纽深基础开挖问题.     

多层住宅砖混房屋设计中两点问题的探讨

浅议多层住宅砖混房屋中构造柱的作用及设置方法；探讨了砖混结构墙下条形基础底面积重复利用问题及其解决方法。     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

大红山铜矿岩体结构调查分析

大量工程实践已证明岩体结构是控制岩体稳定性的重要影响因素。为此，以大红山铜矿为研究背景，在选定有代表性调查地段的基础上，引入详细观测线法对其岩体结构进行了详细调查与统计。分析结果表明：调查区域内巷道岩体节理裂隙比较密集和发育，主要发育有倾向N53E、走向N37W、倾角53°，倾向W26S、走向N36W、倾角68°；倾向E1S、走向NIE、倾角89°的三组优势结构面，其中优势结构面第二组和第三组构成不稳定块体，并且断层及软弱夹层比较发育，加剧了巷道的破碎程度，对巷道围岩的稳定性有控制作用。最后提出了在巷道施工中密切注意围岩稳定性变化，避免工程事故的发生的建议。