提高热采注汽系统热效率的研究

为了降低热采成本和提高经济效益 ,建立了热采注汽系统热效率的数学模型。根据实测数据计算了 9个注汽系统的热效率。提出了改进注汽系统热效率的行之有效的措施。根据排烟的氧含量的大小 ,可以确定注汽锅炉热效率改进程度 ;按管线允许热损失量和保温材料种类 ,设计保温层厚度 ,可大大提高输汽管线热效率。仅此两项 ,即可使大部分注汽系统热效率提高 7%以上 ,井底蒸汽干度提高 10 %以上。     

醋酸甲酯在Cs_(1.5)PW/SiO_2催化剂上的水解反应

通过改变阳离子的种类与配比,制备了一系列SiO2负载的磷钨酸盐催化剂,考察了制备方法对催化剂性能的影响,采用傅里叶变换红外光谱、X射线衍射、X射线荧光光谱、环境扫描电子显微镜等方法对催化剂进行了表征,并考察了该系列催化剂对醋酸甲酯水解反应的活性。实验结果表明,Cs1.5PW/SiO2催化剂的活性最好,当Cs1.5PW负载量(质量分数)为30%时,Cs1.5PW的Keggin结构保持完好,没有硅钨酸阴离子形成,Cs1.5PW在SiO2载体上高度分散;在反应温度55℃、反应时间2h的条件下,醋酸甲酯的转化率为35.79%,约为均相磷钨酸催化剂的1.3倍。该催化剂重复使用4次后,醋酸甲酯的转化率稳定在25%;80℃下反应2h,与NKC-9磺酸树脂催化剂相比,醋酸甲酯的转化率提高了5.17%。     

冷凝水回收技术在立井水暖的应用

采取冷凝水回收先进技术解决了立井水暖锅炉高温冷凝水回收利用问题     

Creep of aromatic polyamide fibres

Creep of Kevlar 29, Kevlar 49 and PRD 49-III fibres was investigated. The fibres exhibited transient creep and the strain-time relationship was represented by a logarithmic time law. The creep strain recovered with time when the load was removed. Upon reloading to the same creep stress the strain-time relationship was again logarithmic but the creep rate was reduced. Modulus measurements were made during the creep test and these showed that the modulus increased with time. This result indicated a crystallite rotation mechanism which could account for the experimentally observed creep strain. Creep in PRD 49-III fibres exhibited a small temperature dependence over the temperature range 20°C to 150°C. The apparent creep activation energy was consistent with the range of values reported for hydrogen bonding. This suggests one possible creep mechanism in which the combined action of stress and thermal activation causes rearrangement of intercrystalline bonds in the crystallite boundaries resulting in boundary creep. Boundary creep allows crystallite rotation which produces the macroscopic creep strain. Boundary creep is discussed in terms of the fibre morphology and a model of delayed elasticity.     

Spontaneous emulsification aspect of enhanced oil recovery

Recent studies have suggested the possibility of spontaneous emulsification as a mechanism for enhanced oil recovery (EOR). The discussions have, however, remained essentially qualitative. A study was therefore undertaken to estimate quantitatively the contribution of spontaneous emulsification as an EOR mechanism. The tests were conducted on several bulk liquid/liquid systems as well as by displacement experiments in unconsolidated synthetic sand packs. Spontaneous emulsification was found to be a mechanism for EOR: the estimated extra contribution to EOR due to this mechanism was found to be significant in laboratory scale displacement experiments. Tertiary recovery was always greater when spontaneous emulsification was evident than otherwise. Results of tests on bulk liquid/liquid systems indicate that the occurrence or absence of spontaneous emulsification can be correlated with the values of ‘partition parameter’. It may be concluded that higher oil recoveries may be achieved in chemical EOR processes where interface mass transfer (and the accompanying spontaneous emulsification) occurs. The evaluation of efficiency of residual oil mobilisation through the capillary number theory (with and without spontaneous emulsification) is also discussed. Displacement tests with spontaneously emulsifying systems showed that residual oil left behind a conventional waterflood was mobilised in a range of capillary numbers much less than that which applies to low-tension waterfloods.     

热环工作特性的理论分析与实验研究

热环是用于非相邻冷热源间热量传递或余热回收的节能装置。本文对热环的基本原理、特点进行了简要介绍 ,在此基础上 ,分析建立了热环的输热能力、输热系数、工作温度等性能指标的计算方程 ,并进行了较系统的实验研究     

固液相变蓄能的数学模型和自然对流换热系数的实验研究

引入自然对流换热系数 ,将固液蓄能数学模型简化为仅用能量方程加以描述。并通过实验测得相变过程的实际温度场 ,证明了自然对流固液相变换热的影响不可忽略 ,验证了固液相变界面移动速率随自然对流换热系数的增大而增大的定性关系     

二级采油技术在文南油田的应用

为解决文南油田高油气比井泵效低的问题，引进了二级采油技术。该技术采用特殊的二级采油工具，充分利用油井高油气比的特点，从而达到提高泵效的目的。文南油田30口井的现场试验表明，该技术应用后，平均单井泵效提高6%以上，平均单井视动液面下降739m，累积增油7560t。     

迅速发展的有机电致发光(OEL)显示器件

有机电致发光显示器件以其全固体、自发光、宽视角、高对比、快响应、低功耗、更轻薄等比液晶显示器件更为优越的特性 ,在小尺寸平板显示市场上正开始向 LCD挑战     

改进催化裂解装置再生立管气固输送状态

荆门分公司催化裂解装置由于使用高堆密度催化剂，再生立管出现了气固输送故障，对反应温度和产品收率影响较大。采取改进措施后取得了显著效果，液化气收率可提高约4个百分点，丙烯收率可提高1－3个百分点。